14
MANUAL TUNING
TUNING THE TV CHANNELS
(CONTINUED)
1
Press TV/VCR to select TV/VCR
mode.
Press MENU.
Press
or to select the
CHANNEL SETUP mode, then
press ENTER.
In certain areas of the countries which have
poor reception the Automatic Tuning System
may not tune your unit to the strongest
broadcast signal. If you are not satisfied with
the automatic tuning then select the Manual
Tuning.
Press
or to select the CH
TUNING mode, then press
ENTER.
2
Press
or to search the
broadcast stations. Each time a
station is found the search will
stop. Press or to continue
searching until all the stations
you want are found, then press
ENTER to store the station you
have selected.
3
TO SKIP A CHANNEL
To skip unwanted channels press CH/
PAGE to select the channel you want to
skip. Then press CANCEL. The channel
number flashes.
To cancel the skip setting, select the
skipped channel using Direct Channel
Selection, then press CANCEL.
4
Press
or to select the
required channel number (1-
110). Press ENTER to store
the channel number. The unit
channels can be preset to
different TV broadcast chan-
nels anytime simply by
repeating step 3-4.
SELECT
TV SETUP
ENTER
EXIT
: ENTER
: MENU
CHANNEL SETUP
AUTO REPEAT [OFF]
SYSTEM SETUP
TIMER REC SET
:
▲▼
CHANNEL SETUP
SELECT
AUTO TUNING
ENTER
EXIT
: ENTER
:
▲▼
: MENU
CH TUNING
CH ALLOCATION
CH 1
SEARCH :
/ F.TUNE :
EXIT : MENU
CH 1
OK
CH
: ENTER
:
/ 0-9
EXIT : MENU
If you can not get a clear picture,
press
or until the picture
becomes clear. When you have a
clear crisp picture store this
setting by pressing ENTER.
When all required stations have
been set, press MENU 3 times to
return to normal TV screen.
15
ENGLISH
TV OPERATION
1
Press ON/STANDBY. Then press TV/VCR to select TV/
VCR mode.
Press Direct Channel Selection.
2
The VOLUME can be adjusted
to a desired level by pressing
or –. The VOLUME
control is represented by a
green bar on the screen.
3
NOTE:
If the station being viewed stops
broadcasting, the TV will shut off after
15 minutes.
Press one of keys 1-9
as required.
Press the two or three
digits in order from left
to right.
1-9:
10-110:
+0
VOLUME
32
16
TV OPERATION (CONTINUED)
To cut off the sound, press this button once. The unit will
be silenced and the symbol “MUTE” will appear on the
screen. The muting can be released by pressing MUTE
again or or –.
MUTE
USING CH/PAGE
OR
BUTTON
Press and release CH/PAGE
or
.
For channels to change properly, they must be correctly
tuned into the unit's memory (P.12-14).
This button allows you to go back to the last channel
selected by pressing CHANNEL RETURN. Press this
button again to return to the last channel you were
watching.
CHANNEL RETURN
SLEEP
To set the TV to turn off at a set time, press SLEEP on the
remote control. The clock will count down 10 minutes each
time the button is pressed in the order of 120, 110.....20,
10, 0. After the sleep time is programmed, the display will
disappear and will reappear every 10 minutes. To confirm
the sleep time setting, press SLEEP once and the
remaining time will be momentarily displayed. To cancel
the sleep time, press SLEEP repeatedly until the display
turns to 0.
DISPLAY
Press DISPLAY. The current time, channel number, real
time tape counter, tape speed and VCR operation etc. will
be indicated.
Press DISPLAY again to remove the call display.
NOTE:
If SLEEP is pressed when the unit is the REC
mode, the clock will count down and the picture
will shut off at the set time, but the recording
continues.
CH 2
01 : 30 : 21 SP
11 : 30 SAT
TV/VCR
Current time
VCR operation
Channel No.
Real Time Tape Counter
Auto Repeat
Tape In
Tape Speed
TV/VCR mode or DVD mode
17
ENGLISH
PICTURE CONTROL ADJUSTMENTS
The picture settings have been factory
adjusted under optimum signal recep-
tion. However, conditions may not be
the same in your area. After tuning in the
unit, allow it to warm up for a few min-
utes. If the picture is not to your liking,
make the following adjustments using
the remote control.
1
To adjust the picture, press
MENU.
Press
or to select the TV
SETUP mode, then press
ENTER.
Press
or to select the
PICTURE mode, then press
ENTER.
2
Press ENTER until your desired
PICTURE mode appears eg.
BRIGHTNESS, CONTRAST,
COLOUR, SHARPNESS. Then
press
or to adjust the level
of the PICTURE.
(See the below for detail.)
3
After finishing the adjustment, press MENU 3 times to
return to normal TV screen.
4
NOTE:
To resume the normal picture adjust-
ment, press CANCEL, while in the
picture mode menu.
Preparation
Press TV/VCR to select TV/VCR mode.
Each time you press ENTER the picture adjustment Screen
changes as follows.
BRIGHTNESS
Press ENTER until “BRIGHTNESS” appears on the screen, then
press
or to adjust the brightness. When is pressed, the
darker portions of the picture become lighter.
SHARPNESS
Press ENTER until “SHARPNESS” appears on the screen, then
press
or to adjust the sharpness.
In weak reception areas, the picture may be more pleasing when
the SHARPNESS is set at a lower level.
NOTES:
• The picture settings can only be adjusted by using or
and ENTER when they are displayed on the screen.
• Press MENU 3 times to return to normal TV screen.
• The On-screen display will disappear about one minute
after finishing an adjustment.
CONTRAST
Press ENTER until “CONTRAST” appears on the screen, then
press
or to adjust the contrast. Pressing improves the
contrast and enhances the colour. Picture looks sharper in the
daytime by increasing the contrast level and sharper at night by
lowering the contrast level.
COLOUR
Press ENTER until “COLOUR” appears on the screen, then press
or to adjust the intensity of the colours. This should be set to
where the colours appear normal in intensity and brilliance.
TIMER REC SET
AUTO REPEAT
OFF
CHANNEL SETUP
TV SETUP
SYSTEM SETUP
EXIT
ENTER
SELECT
: MENU
: ENTER
:
ON/OFF TIMER SET
PICTURE
NICAM
TV SETUP
EXIT
ENTER
SELECT
: MENU
: ENTER
:
AUTO
NEXT
RESET
SET
: ENTER
EXIT : MENU
: CANCEL
:
BRIGHTNESS
0
Summary of Contents for VTW21FQR
Page 116: ......