manualshive.com logo in svg

Toshiba TOSVERT IPE001Z, Instruction Manual

Share
Download
Toshiba TOSVERT IPE001Z Instruction Manual Download Page 14

 

 

E6581580

 

5.  Command & Setpoint selection (Local/Remote)

 

Indication to display Local/Remote mode is on the inverter unit (Refer to the inverter 
instruction manual for details). EtherNet/IP™ option command and setpoint are 
activated on Remote mode. 
 
Inverters have some switches to select the command and setpoint location. Following 
figure shows the diagram. Refer to the inverter instruction manual for the parameter in 
detail. 
 

 

Command

Setpoint

Operation Panel 

EASY key 

(

f750

=

2

)

(Local/Remote key) 

Logic input = 48 (SC/LC)

Network cancel switch

Network (EtherNet/IP)

Network (EtherNet/IP)

0 

1 

ON 

OFF 

0 

1 

Operation Panel 

ON 

OFF 

Control Terminal (VI)

Control Terminal (RR)

: 

Operation Panel

: 

Network (EtherNet/IP)

: 

fmod 

1 

2 

:

 

4 

: 

7 

Control Terminal

Operation Panel

: 

Network (EtherNet/IP)

cmod 

0 

1 

: 

4 

Remote 

Local 

Remote 

Local 

*1 

*1 

 

*1 Command and Setpoint can be selected by following parameters or object. 

FA06, Control Supervisor Object, Instance 71, Instance 100, Instance 101, Instance 
151 

 

 
 

- 13 - 

Summary of Contents for TOSVERT IPE001Z

















Reviews:

No comments

Brands by name

Popular brands

Load more brands