43
Operations
42
Using the menus (Continued)
[
Key lock
]
Protect from operating errors by locking on the control panel buttons of the
projector. (The remote control operations are available.)
Control panel operations are locked after the setting is done, and accordingly
operation with the control panel buttons is disabled.
• To release the key lock, set the [
Key Lock
] to [
Off
] using remote control. Pressing
the [
RETURN
] button on the projector for 10 seconds also sets the [
Key Lock
] to
[
Off
]. (When operating the main unit, the 2 indicators of LAMP and TEMP light in
orange for 3 seconds, and at the same time the projector beeps.)
■
Displaying Information (Status display)
This displays information about the input signal, lamp use time, etc.
“Yes”: displayed, “No”: not displayed
Item
Description
Computer Y/P
B
/P
R
Video S-video
Projector
Input
Input source name
Yes
Yes
Yes
Yes
Mode name
RGB input mode
[Note 1]
Yes
No
No
No
Resolution
Resolution (in dots)
Yes
No
No
No
Frequency
Sync frequency
Yes
No
No
No
Sync
Sync signal polarity
[Note 2]
Yes
No
No
No
Signal format
Y/P
B
/P
R
signal format
No
Yes
No
No
Video mode
Color method of video signal
No
No
Yes
Yes
Lamp time
Time of lamp use
[Note 3]
Yes
Yes
Yes
Yes
Lamp reset count The count for lamp replacement
Yes
Yes
Yes
Yes
Total time
The total time that this projector is used.
Yes
Yes
Yes
Yes
Version
Firmware version
[Note 4]
Yes
Yes
Yes
Yes
Notes
1: The mode of supported RGB signals
p.52
is shown.
2: Sync signal polarity shown as P (positive) or N (negative) for [H/V].
3: Displays [
Lamp time
] as a measure of when the lamp should be replaced. (Cannot be used as
a counter of guaranteed lamp time.) Please replace the lamp after 2000 hours of use if [
Lamp
power
] is set to [
Standard
], or after 3000 hours of use if [
Lamp power
] is set to [
Low
], consult
with a dealer about getting replacement for lamp TLPLW11 (sold separately).
4: [
Version
] shows the version of the projector’s internal control program. This version is referred
to for customer service, etc.
Note
• The displayed information will not be refreshed if the status changes. To refresh the
information, dismiss the display, then display it again.
Default setting 2 menu
Description
Item
Sets projection mode in accordance with Placement Style.
Sets the cooling fan speed.
When two or more projectors are used and controlled by the remote
control respectively, this menu sets the code for the projector and the
remote control.
[ or : Enter setting mode] [ : Select from
1
,
2
,
3
,
4
]
[ :Confirm] [ :Select
OK
to end]
Press [
Cancel
] to return.
Lock the control panel buttons.
[ or : Enter setting mode] [ : Select
On/Off
]
[ :Confirm] [ :Select
OK
to end]
Press [
Cancel
] to return.
Press . (The password and user logo are not reset.)
Resets all adjustments and settings to their factory settings.
Password setting
Projection
mode
Fan mode
Remote
control
Key lock
Reset all
Password
Yes No
Standard High
(Rear ceiling)
(Standard)
(Rear)
(Ceiling)
p.21
p.32
Detailed description
[
Fan mode
]
Setting [
Fan mode
] to [
High
] increases the cooling fan speed. (The cooling fan
noise gets louder.) Set this option to use the projector, for example, at high altitude
(over 1,500 meters above sea level).
• Do not set Fan mode to [
High
] when using the projector at a lower altitude.
[
Remote control
]
Sets a remote control code from 4 types. You can set each code respectively for up
to 4 projectors. The factory setting is [
1
].
To switch codes, set the same code for the projector and the remote control.
A remote control code is applied after the setting is done.
• You cannot operate the remote control if the codes of the projector and the
remote control do not match.
Remote control code setting for remote control
Remove the battery cover and set the same
remote control code switch
as the
projector.
p.16
p.17
(Use a screwdriver with thin tip to set.)
Summary of Contents for TLP-WX2200
Page 29: ......
