background image

Projector Driver Application Note

Toshiba TLP-560

Revision A

DR-TSH3 – 10/8/02

SP Controls reserves the right to modify specifications without notice at any time.

This document describes the 

SmartPanel

 Projector Driver for the 

Toshiba TLP-560 

projector. For

information on configuring and using the Panel, see the 

SmartPanel Configuration and Installation Guide.

I. PROJECTOR CONTROL

A.   Volume and Power Control

Volume control on the Toshiba is 

relative

. Absolute volume control for this model is possible with use of

SP Controls’ optional 

Audio Follow Video Pre-Amplifier

.

B.   Input Selection Mapping

The following table specifies the factory preset input mapping for this Driver. The 

Configuration Utility

can be used to customize these settings your installation. NOTE: 

Inputs 2 and 4 select the same

Projector Input.

Selection 1:

COMPUTER

Selection 2:

VIDEO

Selection 3:

S-VIDEO

Selection 4:

VIDEO

Input choices available with this Driver are RGB,
VIDEO/S-VID, and CAMERA.  The VIDEO/S-VID
port can be used as either an RCA video input
OR an S-Video input 

but not both

.

C.   Hidden Function Mapping

The following table specifies the factory preset hidden function mapping for this Driver. The

Configuration Utility

 can be used to customize these settings your installation.

Selection 1:

ADJ -

Selection 2:

ADJ +

Selection 3:

ADJUST LEFT

Selection 4:

ADJUST RIGHT

Off:

MENU / SELECT

Volume Up:

ADJUST UP

Volume Down:

ADJUST DOWN

Hidden functions names are based on Toshiba documentation. 

Adjust

 controls navigate through

onscreen menus. Hidden functions are accessed by pressing the indicated key while the holding the 

On

key down.

The hidden functions available for the Toshiba with this Driver are as follows.  Note that the functions
available will vary depending on the model of projector you are controlling:

MENU / SELECT
ADJUST LEFT
ADJUST RIGHT
ADJUST UP
ADJUST DOWN

AUDIO MUTE ON
AUDIO MUTE OFF
ALL MUTE ON
ALL MUTE OFF
FREEZE ON


ADJUST –
Picture in Picture ON
Picture in Picture OFF
FREEZE OFF

Projector

Ready

Warm-up

OFF

ON

Volume

INPUT 1

INPUT 2

INPUT 3

INPUT 4

Projector

Ready

Warm-up

OFF

ON

Volume

ADJUST

 UP

ADJUST

 DOWN

MENU / SELECT

ALL MUTE

OFF

ADJUST

LEFT

ADJUST

 RIGHT

ALL MUTE

ON

Summary of Contents for TLP-560






Reviews: