Toshiba STRATA CIX DKT Administrator'S Manual Download Page 11

Page: 11 / 72

Strata CIX Telephones Administrator Manual 06/06

Administrator Mode

This chapter contains some of the functions that can be performed using
Administrator Mode.

Important!

These functions require Strata CIX release 4.1 or higher software.

You can access the Administrator mode using DKT3000/3200/3500-series telephones.
Toshiba recommends using any 2-line display telephone.

To access the Admin mode, the telephone must be enabled for this function in system
programming by the telephone system administrator.

Functions

Using the soft keys on your telephone, you can program the following functions in
Administrator mode:

•

Phone Name – enter the Extension (PDN) name for any telephone in the Strata
CIX

•

Door Name – enter door phone name

•

System SD/Name

– enables you to program system speed dial names

•

Station SD/Name

– enables you to program station speed dial names for any

station in the system

•

Exchange Line Name – program Exchange line names

•

DNIS Name – program DNIS names

The Admin telephone mode allows speed dial names to be programmed but the actual speed dial numbers
are programmed using the speed dial programming procedures in this guide.

Summary of Contents for STRATA CIX DKT









































































Search results

Summary of Contents for STRATA CIX DKT

Reviews:

Related manuals for STRATA CIX DKT

Brands by name

Popular brands

Toshiba STRATA CIX DKT, Administrator'S Manual

Search results

Summary of Contents for STRATA CIX DKT

Reviews:

Related manuals for STRATA CIX DKT

Brands by name

Popular brands