Toshiba STRATA CIX DKT Administrator'S Manual Download Page 42

Page: 42 / 72

IPT2008-SDL Settings

Configurations

Strata CIX Telephones Administrator Manual 06/06

IP Address for DNS Server (Primary Name Server)

Note

If DHCP Mode is ON, you don’t have to set any parameters for the DNS server.

1. Select Configuration > Advanced > P-DNS. The

Primary DNS Address screen displays (shown
right).

2. Follow the steps to change settings on

page 27

IP Address for DNS Server (Secondary Name Server)

1. Select Configuration > Advanced > P-DNS. The

Primary DNS Address screen displays (shown
right).

2. Follow the steps to change settings on

page 27

GRQ Port Number

1. Select Configuration > Advanced > GRQ Port.

The current GRQ Port Number displays
(shown right).

2. Enter the New number.

3. Press the SET soft key to accept the change

...or press the CANCEL soft key to cancel the
change and go to the Network Setting screen.

Note

For other notes, refer to

“Station ID” on

page 29

Primary DNS Address

192.168.0.234 :Current

:New

Backspace = Vol-Down.

[SET] [CANCEL]

CONFIG

PHONE

WEB

Secondary DNS Address

192.168.0.235 :Current

:New

Backspace = Vol-Down.

[SET] [CANCEL]

CONFIG

PHONE

WEB

GRQ Port Number

0 :Current

:New

Backspace = Vol-Down.

[SET] [CANCEL]

CONFIG

PHONE

WEB

Summary of Contents for STRATA CIX DKT









































































Search results

Summary of Contents for STRATA CIX DKT

Reviews:

Related manuals for STRATA CIX DKT

Brands by name

Popular brands

Toshiba STRATA CIX DKT, Administrator'S Manual

Search results

Summary of Contents for STRATA CIX DKT

Reviews:

Related manuals for STRATA CIX DKT

Brands by name

Popular brands