Toshiba RAV-SP1104AT7 Service Manual Download Page 120

Page: 120 / 143

– 120 –

No.

Part name

Side cabinet

Procedure

1. Detachment

1) Carry out the operation in 1. of

above.

2) Remove the screws fixing the inverter assembly

and the side cabinet. (ST1T Ø4 × 10, 3 pcs.)

3) Remove the screws for the side cabinet and the

valve fixing plate. (ST1T Ø4 × 10, 2 pcs.)

4) Remove screw for the side cabinet and piping

panel (rear). (Hexagonal screw Ø4 × 10, 2 pcs.)

5) Remove screw for the side cabinet and the

bottom plate. (Hexagonal screw Ø4 × 10, 1 pc.)

6) Remove screws for the side cabinet, heat

exchanger and the fin guard.
(Hexagonal screw Ø4 × 10, 5 pcs.)

2. Attachment

1) Temporarily suspend the side cabinet on the

inverter assembly using the hook.

2) Mount the removed screws in the opposite

procedure to that during detachment.

Remarks

Valve fixing plate

Discharge port cabinet

Inverter ass’y

Side cabinet

Hook

Summary of Contents for RAV-SP1104AT7















































































































































Search results

Summary of Contents for RAV-SP1104AT7

Reviews:

Related manuals for RAV-SP1104AT7

Brands by name

Popular brands

Toshiba RAV-SP1104AT7, Service Manual

Search results

Summary of Contents for RAV-SP1104AT7

Reviews:

Related manuals for RAV-SP1104AT7

Brands by name

Popular brands