Toshiba RAV-SP1104AT7 Service Manual Download Page 119

Page: 119 / 143

– 119 –

Heat exchanger

Motor base

Discharge
port cabinet

Bottom plate

Fin guard

No.

Part name

Discharge
port cabinet

Procedure

1. Detachment

1) Carry out the operation in 1. of

above.

2) Remove the screws fixing the inverter assembly,

the discharge port cabinet and the partition board.
(ST1T Ø4 × 8, 4 pcs.)

3) Remove the screws for the discharge port cabinet

and the bottom plate.
(Hexagonal screw Ø4 × 10, 2 pcs.)

4) Remove screw for the discharge port cabinet and

heat exchanger. (ST1T Ø4 × 8, 1 pc.)

5) Remove screw for the discharge port cabinet and

the motor base. (ST1T Ø4 × 8, 2 pcs.)

6) Remove screws for the discharge port cabinet

and the fin guard.
(Hexagonal screw Ø4 × 10, 2 pcs.)

2. Attachment

1) Attach the discharge port cabinet and end board

of heat exchanger and fix with a screw.
(ST1T Ø4 × 8, 1 pc.)

2) Mount other removed screws into original

positions.

Remarks

Summary of Contents for RAV-SP1104AT7















































































































































Search results

Summary of Contents for RAV-SP1104AT7

Reviews:

Related manuals for RAV-SP1104AT7

Brands by name

Popular brands

Toshiba RAV-SP1104AT7, Service Manual

Search results

Summary of Contents for RAV-SP1104AT7

Reviews:

Related manuals for RAV-SP1104AT7

Brands by name

Popular brands