Toshiba RAS-3M26S3AV-A Installation Manual Download

Page: 13 / 16

Outdoor Unit

Installation Manual

■

Connection procedure

•  This air conditioner complies with AS/NZS 4755.3.1.
•  DRM available: DRM1, DRM2, DRM3
•  The terminal block meets ELV requirements.

COM DRM1 DRM2 DRM3

1 2 3

COM DRM1 DRM2 DRM3

MCC-1653

DRED

Demand response interface

Trans-

former

Outdoor control

P.C. board

CN101

CN102

CN100

CN105

Locally procured

Power supply

Indoor (A~E) unit

Connecting

WARNING

• Do not connect the DRED mains cable to the terminal block of the outdoor unit

(Power supply and Indoor/Outdoor connecting). Improper installation may result
in

re.

• For the power supply of the DRED, prepare exclusive power supply separated from

that of the outdoor unit.

WARNING

Connect the wire (4-wire) with a round terminal to the Demand section (COM, DRM1,
DRM2, DRM3) on the terminal block.

1116791101_EN.indd 12

2/3/58 BE 2:20 PM

Summary of Contents for RAS-3M26S3AV-A

















Search results

Summary of Contents for RAS-3M26S3AV-A

Reviews:

Related manuals for RAS-3M26S3AV-A

Brands by name

Popular brands

Toshiba RAS-3M26S3AV-A, Installation Manual

Search results

Summary of Contents for RAS-3M26S3AV-A

Reviews:

Related manuals for RAS-3M26S3AV-A

Brands by name

Popular brands