8
Stripping length of the connecting cable
NOTE
: Connecting cable
• Wire type : More than H07RN-F or 60245 IEC66 (1.0 mm
2
or more).
0
1
0
1
0
1
0
1
30
30
40
40
L N
1 2 3
1
2
L
N
3
Connecting cable
Power cord
Earth line
Earth line
Connecting
cable
Terminal
block
Power
cord
CAUTION
• Wrong wiring connection may cause some electrical parts burn out.
• Be sure to comply with local cords on running the wire from indoor unit
to outdoor unit (size of wire and wiring method, etc.).
• Every wire must be connected
fi
rmly.
• If incorrect or incomplete wiring is carried out, it will cause an ignition or
smoke.
• Prepare the power supply for exclusive use with the air conditioner.
• This product can be connected to the mains.
Connection to
fi
xed wiring: A switch which disconnects all poles and
has a contact separation of at least 3 mm must be incorporated in the
fi
xed wiring.
Wiring Connection
1. Remove the valve cover from the outdoor unit.
2. Connect the connecting cable to the terminals as identi
fi
ed with their
respective matched numbers on the terminal block of indoor and outdoor
unit.
3. When connecting the connecting cable to the outdoor unit terminals, make
a loop as shown in the installation diagram of indoor and outdoor unit to
prevent water coming in the outdoor unit.
4. Insulate the unused cords (conductors) from any water coming in the outdoor
unit. Proceed them so that they do not touch any electrical or metal parts.
OTHERS
OTHERS
Gas Leak Test
Test Operation
Auto Restart Setting
The product was shipped with Auto Restart function in the off position.
Turn it on as required.
How to set the Auto Restart
Remote Control A-B Selection
To separate using of remote control for each indoor unit in case of 2 air
conditioner are installed near.
Remote Control B Setup.
1. Press [RESET] button on the indoor unit to turn the air conditioner ON.
2. Point the remote control at the indoor unit.
3. Push and hold [CHECK] button on the Remote Control by the tip of the
pencil. “00” will be shown on the display (Picture
1
).
4. Press [MODE] during pushing [CHECK]. “B” will show on the display
and “00” will disappear and the air conditioner will turn OFF. The Remote
Control B is memorized (Picture
2
).
• When two indoor units are installed in the same room or adjacent two
rooms, if operating a unit, two units may receive the remote control signal
simultaneously and operate. In this case, the operation can be preserved
by setting either one remote control to B setting. (Both are set to A setting
in factory shipment.)
• The remote control signal is not received when the settings of indoor unit
and remote control are different.
• There is no relation between A setting/B setting and A room/B room when
connecting the piping and cables.
• Check the
fl
are nut
connections for the gas leak
with a gas leak detector or
soap water.
This product is designed so that, after a power failure, it can restart automatically
in the same operating mode as before the power failure.
RESET button
Check places for
the indoor unit.
Check places for
the outdoor unit.
Information
To switch the TEST RUN
(COOL) mode, press [RESET]
button for 10 seconds. (The
beeper will make a short beep.)
1. Press and hold the [RESET] button on the indoor unit for 3 seconds to
set the operation. (3 beep sound and OPERATION lamp blink 5 time/sec
for 5 seconds)
2. Press and hold the [RESET] button on the indoor unit for 3 seconds to
cancel the operation. (3 beep sound but OPERATION lamp does not
blink)
• In case of ON timer or OFF timer are set, AUTO RESTART
OPERATION does not activate.
Note : 1. Repeat above step to reset Remote Control to be A.
2. Remote Control A have not “A” display.
3. Default setting of Remote Control from factory is A.
1
2
Model
RAS-13, 16N3KCV Series
Power source
50Hz, 220 – 240 V Single phase
60Hz, 220 – 230 V Single phase
Maximum running current
9A
Plug socket & fuse rating
12A
Power cord
H07RN-F or 60245 IEC66 (1.5 mm
2
or more)
Electric parts
cover
Valve cover
1110251267-EN.indd 8
1110251267-EN.indd 8
6/29/12 11:43 AM
6/29/12 11:43 AM