Toshiba MCY-MAP0401HT2DZ, Owner'S Manual

Page: 13 / 24

EN
– 12 –
◆
To stop swinging
1
Push the button at the desired
position while the louver is swinging.
• Push the button repeatedly to change
the louver position again.
In this case, push the button again after 2
seconds.
• In COOL / DRY operation, the louver does not
stop as it directs downward. If stopping the
louver as it directs downward during swing
operation, it stops after moving to the third
position from the highest position.
◆
Unit select
• When two or more indoor units are controlled with
one remote controller, the louver direction can be set
for each indoor unit by selecting them individually.
• To set louver direction individually, push the
button (left side of the button) to display an indoor
unit number in the control group. Then set the louver
direction of the displayed indoor unit.
• When no indoor unit number is displayed, all indoor
units in the control group can be controlled
simultaneously.
• Each time you push the (left side of the
button), the indication changes as follows:
„
4-way cassette type only
◆
To set the louvers individually
1
Push the button (left side of the
button) during running to select a unit.
The unit number changes each time you push the
button.
• When no unit number is displayed, all units are
selected.
2
Push the button (right side of the
button) to select a louver.
Each time you push the button, the indicator on the
left of the remote controller changes as follows:
* When no louver number is displayed, all 4
louvers are selected.
* However, even if the button is pushed
while the louver is swinging, one of the
indications below may sometimes be displayed
and may not set the louver to the highest
position.
▼
Indications when swinging is stopped
▼
Indications when swinging is stopped
SWING/FIX
SWING/FIX
SWING/FIX
FAN / HEAT COOL / DRY
SWING/FIX
FAN / HEAT
operation COOL / DRY
operation
UNIT LOUVER
UNIT LOUVER
Unit No.
1-4
No
display
Unit No.
1-1
Unit No.
1-2
Unit No.
1-3
UNIT LOUVER
No
display
Unit No.
1-1
Unit No.
1-2
Unit No.
1-3
Unit No.
1-4
UNIT LOUVER
No
display
Louver No.
03
01
02 04
Refrigerant
pipe
Drain pipe
Electrical control box
3
Push the button to confirm the
direction of the selected louver.
Each time you push the button, the indication
changes as follows:
* When cooling or drying, (4) and (5) are not
displayed.
◆
Setting the swing pattern
1
Push and hold the FIX for at least 4
seconds while the operation is stopped.
blinks.
2
Push the button (left side of the button)
to select a unit.
The unit number changes each time you push the
button.
The fan of the selected unit runs, and the louver
swings.
3
Push the buttons to select a swing
type.
REQUIREMENT
Do not set “0000”.
(The louver may be damaged.)
4
Push the button.
5
Push the button to finish the setting.
▼
Standard swing
All four louvers swing simultaneously at the same
angle.
▼
Dual swing (Recommended for heating)
• Adjoining louvers alternately point horizontally and
downward to heat the room evenly.
• Air blown downward reaches the floor, and air blown
horizontally is spread to circulate heat.
Swing code Movement pattern
0001
Standard swing
(factory default)
0002 Dual swing
0003 Cyclic swing
SWING/FIX
(1) (2) (3) (4)
(7) (6) (5)
SWING/FIX
UNIT LOUVER
No
display
Unit No.
1-1 Unit No.
1-2 Unit No.
1-3
Unit No.
1-4
Swing code
Swing
Horizontal
Downward
Downward
Horizontal
Downward
Downward
Horizontal
Horizontal
23-EN 24-EN