background image

Safety Precautions 

Safety Precautions 

 

 

OIS-DS52 and the instruction manual give important information for using products 

safely. It helps prevent damage to properties and hazard to people who use them or to 
others. 

 

Make yourself familiar with the signal words and signs in this page then read the 

safety precautions that follow and always follow the instructions to avoid hazards. 

 

Explanation of signal words 

 

Signal word is a word that designates a degree or level of hazard seriousness.  

 

The words WARNING and CAUTION are used for the products. 

 

WARNING

 

Indicates a potentially hazardous situation which could result in death or 
serious injury, if you do not follow the instructions. 

CAUTION

 

Indicates a potentially hazardous situation which may result in minor or 
moderate injury and/or property damage, if you do not follow the instructions. 

 

Hazard alert shapes and symbols 

 

Following shapes and symbols are used in the safety precaution labels affixed to the 

products and in other places including operation manuals for giving safety instructions.  
 

 

Filled circle means "Mandatory Action" or "Do as indicated." 
Required action is shown in the circle or described near the circle. 

 

Circle band with a diagonal slash means "Prohibition" or " You must not do." 
Prohibited action is shown in the circle or described near the circle. 

 

Triangle means "Hazard Alerting" or "Be alert against hazard." 
The kind of hazard is shown in the triangle or described near the triangle. 

 

Exclamation point with a triangle is a safety alert symbol which indicates a potential hazard. 
It is used with a Signal Word. 

 

Square or rectangle means "Information Messages" or "Notice." 

 

 Make sure to observe the following points. 

WARNING 

System fault or data loss may occur, if the power fails or the power system (including 
the power switch) is turned off. Toshiba cannot assure any compensation for the 
resulting damages. Take precautions in advance to protect the system in order to 
prevent such event to take place. Also back up your data regularly to minimize the 
possible damage by loss of data as a result of such event. 

 

Summary of Contents for JOKC1





























Reviews: