manualshive.com logo in svg

Toshiba GX9 ASD, Quick Start Manual

Share
Download
Toshiba GX9 ASD Quick Start Manual Download Page 73

GX9 ASD Quick Start Guide

63

User Notification Codes

The 

User Notification

 codes appear on the LED and LCD screens while the associated function is active.

User Notification

 codes notify the user of active functions that are usually only momentary under normal 

operating conditions. 

User notification events are not error conditions and only convey active system functions to the user and 
may be associated with an output contact for annunciation or subsystem activation.

Table 6. User Notification Codes.

LED

Screen

LCD

Screen

Function

Description

Atn

—

Autotune Active

Autotune

 function is active.

db

—

DC Braking

Motor Shaft Stationary

 function is active.

dbOn

—

DC Braking

DC Injection

 function is active.

Pump

Virtual Linear 
Pump On

Virtual Linear 
Pump On

Virtual Linear Pump

 function is enabled and active.

LOFr

Virtual Linear 
Pump Low 
Frequency

Virtual Linear 
Pump Low 
Frequency

Virtual Linear Pump

 function is operating at the 

Low-Frequency 

Limit

 setting (

F919

).

Note:

Some 

User Notification

 conditions and 

Alarms

 may be annunciated via a discrete output 

terminal setting. See the GX9 ASD Installation & Operation Manual for a listing of the possible 
system conditions that may be associated with an output terminal.

Summary of Contents for GX9 ASD





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands