Toshiba GD-1300 Service Manual Download Page 3 | Manualshive

Page: 3 / 78

background image

GENERAL PRECAUTIONS REGARDING THE INSTALLATION
AND SERVICE FOR e-STUDIO203S/203SD AND GD-1300

The installation and service should be done by a qualified service
technician.

1.

Transportation/Installation

- When transporting/installing the machine, be sure to use the positions as indicated below.

The machine is quite heavy and weighs approximately 17 kg (37 lb.), therefore pay full attention
when handling it.

- Be sure to use a dedicated outlet with AC120V/8A, 220-240V/5A, 230-240V/5A for its power

source.

- The machine must be grounded for safety.

Never ground it to a gas pipe or a water pipe.

- Select a suitable place for installation.

Avoid excessive heat, high humidity, dust, vibration and direct sunlight.

- Also provide proper ventilation as the machine emits a slight amount of ozone.
- The socket-outlet shall be installed near the machine and shall be easily accessible.

2.

Service of Machines

- Basically, be sure to turn the main switch off and unplug the power cord during service.
- Be sure not to touch high-temperature sections such as the exposure lamp, the fuser unit and

their periphery.

- Be sure not to touch high-voltage sections such as the chargers and the high-voltage trans-

former.
Especially, the board of these components should not be touched since the electric charge may
remain in the capacitors, etc. on them even after the power is turned OFF.

- Be sure not to touch rotating/operating sections such as gears, belts, pulleys, fan, etc.
- Be careful when removing the covers since there might be the parts with very sharp edges

underneath.

- When servicing the machines with the main switch turned on, be sure not to touch live sections

and rotating/operating sections. Avoid exposure to laser radiation.

- Use suitable measuring instruments and tools.
- Avoid exposure to laser radiation during servicing.

- Avoid direct exposure to the beam.
- Do not insert tools, parts, etc. that are reflective into the path of the laser beam.
- Remove all watches, rings, bracelets, etc. that are reflective.

- Unplug the power cable and clean the area around the prongs of the plug once a year or more.

A fire may occur when dust lies on this area.

«
1
2
3
4
5
...
»

Summary of Contents for GD-1300















































































Reviews:

No comments

Related manuals for GD-1300

Brand: Samsung Pages: 322

Brand: Samsung Pages: 340

Brand: Samsung Pages: 349

Brand: Samsung Pages: 330

Brand: Samsung Pages: 315

Brand: Samsung Pages: 2

Brand: Samsung Pages: 2

Brand: Samsung Pages: 232

Brand: Samsung Pages: 42

SCX-6545N Series

Brand: Samsung Pages: 468

Brand: Samsung Pages: 196

SCX4521F - B/W Laser - All-in-One

Brand: Samsung Pages: 120

Brand: Oki Pages: 320

V16 Automatic Shaker Unit

Brand: Garment Printer Ink Pages: 21

Brand: Muratec Pages: 6

Brand: Xerox Pages: 70

IMAGE L2550DW Series

Brand: G&G Pages: 147

Brand: RHINO Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands