Toshiba EB621 Operation Manual Download Page 61

Page: 61 / 122

6F8C0879

4.2 Ethernet Cable Connection

4.2 Ethernet Cable Connection

Connect the Ethernet cables (AUI cable: 10BASE5; 3D-2V: 10BASE2) to the EN6
modules.

4.2.1

10BASE5 (EN611, EN621, EB621)

(1) Push up the slide lock on the Ethernet connector (EN-A or (EN-B) and connect the

AUI cable.

(2) Push the slide lock down to lock the AUI cable.

Check that the AUI cable connector has been fixed by the slide lock.

(3) Mount the connector clamp and fasten the AUI cable connector to the EN6 module.

Fasten the connector clamp with two M3 screws, using a Phillips screwdriver.

(4) Clamp the AUI cable.

Figure 4-2 Connecting AUI Cable

Figure 4-3 Fastening the Connector with Clamp

Ethernet connector
(slide lock)

AUI cable

EN6 module
or
EB6 module

Connector clamp

AUI cable

EN6 module
or
EB6 module

Summary of Contents for EB621



























































































































Search results

Summary of Contents for EB621

Reviews:

Brands by name

Popular brands

Toshiba EB621, Operation Manual

Search results

Summary of Contents for EB621

Reviews:

Brands by name

Popular brands