Toshiba EB621 Operation Manual Download Page 56

Page: 56 / 122

model 2000 Ethernet Module Operation Manual

Chapter 3 Setting

3.2.9

Default gateway IP address (Router IP address) setting

(1) In using the default gateway (router), Set a default gateway IP address (router IP

address).There is only one default gateway IP address that can be set.

The default gateway can be used only if IPF ON and IP address type [Setting from
Tool] are set using the operation mode switches.

The default gateway function is valid for EN611, EN631, EN651, and EN651A only
(invalid for EN621, EN641, and EN661).

(2) Register a default gateway IP address having the same value as the network address

part (including the subnet) of the IP address for the EN6 module to be registered. (In
the present case, 192.168.0.**)

An example of setting is shown below.

(In the present case, 192.168.0.10 (subnet mask: 255.255.255.0))

Figure 3-6 System Configuration of a Default Gateway IP Address Setting Example

Default gateway

(router)

EN611

Personal computer,

for example

192.168.0.20

192.168.0.10

xx.yy.zz.vv

Summary of Contents for EB621



























































































































Search results

Summary of Contents for EB621

Reviews:

Brands by name

Popular brands

Toshiba EB621, Operation Manual

Search results

Summary of Contents for EB621

Reviews:

Brands by name

Popular brands