Toshiba e-studio 2330C Imaging Manual Download Page 173

Page: 173 / 262

e-STUDIO2330C/2820C/2830C/3520C/3530C/4520C

3-54

* This adjustment will have an effect only on Auto or Color mode printing.

(5) Enter adjustment mode [05]. Increase the values for codes [8110 to 8113] to perform fine adjustment and

increase the sharpness intensity.

•

Adjust the value for [05] code corresponding to the print option to be applied (Color mode and Image

quality type).

Color

mode

Image

quality type

[05] code

Subcode

Recommend

ed value

Acceptabl

e value

range

Default

General 05-8110 0/1/2

Photograph 05-8111 0/1/2

Presentation 05-8112 0/1/2

Auto /

Color

Line Art

05-8113

0/1/2

Set a value

larger than 128.

0 to 255

128

Subcode

Apply to

0 Text
1 Graphics
2 Image

* Set the value in increments of approximately 5, while checking the printouts until the optimum value is

obtained.

<Hint>

This adjustment affects on the following areas according to Image Quality Type:

•

General, Photograph, and Presentation: Only raster data (print image)

•

Line Art:

Only thin lines, small text and raster data

<Note>

This adjustment changes the values set in the MFP. Therefore, it will affect every user who uses

the printer by connecting it to the MFP. After the adjustment, the values changed will be applied

to all printouts for the "Sharpness" option. Carefully perform the adjustment, being aware that

the image quality of all future printouts will be changed, when printing out originals other than

the one that is used for the adjustment.

Precautions after the completion of the adjustment

The adjustment may possibly cause outlined edges, incorrect color of thin lines, jaggies, and variations in

gradation. As a result the photo image may look unnatural. Therefore, carefully perform the adjustment, while

checking the printouts.

PS3

Mac

3. Printer-specific Adjustments

Summary of Contents for e-studio 2330C

































































































































































































































































Search results

Summary of Contents for e-studio 2330C

Reviews:

Related manuals for e-studio 2330C

Brands by name

Popular brands

Toshiba e-studio 2330C, Imaging Manual

Search results

Summary of Contents for e-studio 2330C

Reviews:

Related manuals for e-studio 2330C

Brands by name

Popular brands