12
Introduction
S
LO
W
( ) button
Direction buttons (
/
/
/
)
EJECT button
43
DI
S
PL
A
Y button
Numbered buttons (0-9)
51
26
29
S
UBTITLE button
50
INPUT button
16
ZOOM button
45
MENU button
21
S
ETUP button
57
48
PL
A
Y MODE button
47
51
PL
A
Y button
42
P
A
U
S
E button
43
TOP MENU button
49
RETURN button
G
A
ME button
57
53
T
V/
D
V
D button
42
25
Direct channel selection
buttons (0-9)
25
CH RTN button
CLO
S
ED C
A
PTION button
26
S
KIP ( ) button
44
RE
V
button
44
FF button
44
44
16
PO
W
ER button
JUMP button
45
25
Direct channel selection button ( )
A
UDIO
S
ELECT button
50
MUTE button
26
49
E
X
IT
/
C
A
NCEL button
20
33
S
KIP ( )button
44
S
TOP button
42
44
REPE
A
T
A
-B button
47
PIC
S
IZE button
S
E-R0305
36
ENTER button
20
S
LEEP button
26
*D
V
D MENU button
25
V
OL +
/
– button
20
S
LO
W
( ) button
M
A
RKER button
49
46
A
NGLE button
CH
/
button
42
20
Remote control
The instructions in this manual describe the function on the remote control. See the page in
for details.
*DVD MENU button
Use the DVD MENU button to
display the menu included on
many DVD video discs.
To operate a menu, follow the
instructions in “DVD menu.”
49
Identification of controls (Continued)
Introduction
13
Replace the compartment
cover.
Install two “R03/AAA” batteries
(supplied), paying attention to
the polarity indicated in the
battery compartment.
Open the battery compartment
cover in the direction of the
arrow.
1
2
3
• Aim the remote control at the remote sensor and press control buttons to operate.
•
Operate the remote control within 30° angle on either side of the remote sensor, up to a distance of approx. 5 meters.
Caution:
• Never throw batteries into a fi re.
Note:
•
Be sure to use AAA size batteries.
•
Dispose of batteries in a designated disposal area.
•
Batteries should always be disposed of with the environment in mind. Always dispose of batteries in accordance with
applicable laws and regulations.
•
If the remote control does not operate correctly, or if the operating range becomes reduced, replace batteries with
new ones.
•
When necessary to replace batteries in the remote control, always replace both batteries with new ones.
Never mix battery types or use new and used batteries in combination.
•
Always remove batteries from remote control if they are dead or if the remote control is not to be used for an extended
period of time. This will prevent battery acid from leaking into the battery compartment.
Inserting batteries
Operation
Approx. 5 meters
Connections
14
75 ohm coaxial cable
(not supplied)
300-75 ohm matching
transformer (not supplied)
300-75 ohm matching
transformer (not supplied)
UHF 300 ohm
twin-lead wire
(not supplied)
VHF 300 ohm
twin-lead wire
(not supplied)
UHF 300 ohm
twin-lead wire
(not supplied)
VHF 75 ohm
(not supplied)
Antenna
jack
Antenna
jack
Antenna
jack
Combiner
(not supplied)
Antenna
jack
Combiner
(not supplied)
Connect the 75 ohm cable from the combination
VHF/UHF antenna to the antenna jack on the back
of the TV/DVD.
If your combination VHF/UHF antenna has a 300
ohm twin-lead wire, use the 300-75 ohm matching
transformer (not supplied).
Connect the UHF 300 ohm twin-lead wire to the
combiner (not supplied). Connect the VHF 300 ohm
twin-lead wire to the 300-75 ohm matching transformer
(not supplied). Attach the transformer to the combiner,
then attach the combiner to the antenna jack on the
back of the TV/DVD.
Connect the VHF 75 ohm cable and UHF 300 ohm
twin-lead wire to the combiner (not supplied).
Attach the combiner to the antenna jack on the back
of the TV/DVD.
Combination VHF/UHF antenna (Separate VHF and UHF 300 ohm twin-lead wires)
Antenna connections
If you are using an indoor or outdoor antenna, follow the instructions below that correspond to your antenna system.
If you are using a cable TV service (CABLE), see
15
for Cable TV connections.
Separate VHF/UHF antennas (75 ohm VHF cable and 300 ohm UHF twin-lead wires)
Combination VHF/UHF antenna (Single 75 ohm cable or 300 ohm twin-lead wire)
Connections
15
For basic cable service not requiring a converter/descrambler
box, connect the Cable TV 75 ohm coaxial cable directly to the
Antenna jack on the back of the TV/DVD.
75 ohm
coaxial cable
If you subscribe to a cable TV service in which basic channels are unscrambled and premium channels require
the use of a converter/descrambler box, you may wish to use a signal splitter and an A/B Switch box (available
from the cable company or an electronics supply store). Follow the connections shown below. With the switch in
the “B” position, you can directly tune any nonscrambled channels on your TV/DVD. With the switch in the “A”
position, tune your TV/DVD to the output of the converter/descrambler box (usually channel 3 or 4) and use the
converter/descrambler box to tune scrambled channels.
Incoming 75 ohm
Cable TV
75 ohm cable to
TV/DVD
Antenna
jack
Antenna
jack
Converter/
descrambler
If you subscribe to a cable TV service which requires the use of a converter/descrambler box, connect the
incoming 75 ohm coaxial cable to the converter/descrambler box. Using another 75 ohm coaxial cable, connect
the output jack of the converter/descrambler box to the antenna jack on the TV/DVD. Follow the connections
shown below. Set the TV/DVD to the output channel of the converter/descrambler box (usually channel 3 or 4)
and use the converter/descrambler box to select channels.
For subscribers to basic cable TV service
For subscribers to scrambled cable TV service
For subscribers to unscrambled basic cable TV service with scrambled
premium channels
Splitter
B
A
Incoming
75 ohm
Cable TV
A/B switch
75 ohm cable
to TV/DVD
Converter/
descrambler
Antenna
jack
Cable TV connections
This TV/DVD has an extended tuning range and can tune most cable channels without using a Cable TV converter box.
Some cable companies offer “premium pay channels” in which the signal is scrambled. Descrambling these signals for
normal viewing requires the use of a descrambler device which is generally provided by the cable company.
