background image

2

The following steps must be performed to properly install your DVD-RAM.

Set drive’s jumpers

Connect audio cable

Attach IDE BUS cable

Connect power cable

Mount DVD-RAM

Install CyberLink PowerDVD

 software (used for viewing DVD movies)

Install VOB InstantWritesoftware (used for recording CDs)

SETTING JUMPERS

The mode select jumpers are six (6) straight angle pins located on the rear of the
DVD-RAM. By placing a jumper on the pins, you can select the following func-
tions:

CS: – Drive is configured using host interface signal CSEL
SL: – Configures drive as Slave
MA: – Configures drive as Master (default mode)

Mode Select Jumpers

In most installations, jumper should remain in MA (Master) position (factory
default). It is recommended that you install your DVD-RAM only on the second-
ary IDE BUS. If you are installing on primary IDE BUS, your hard drive would
then be the Master, and you should set your DVD-RAM to the Slave position (SL).

PLACING DVD-RAM INSIDE YOUR COMPUTER

Now that you have set your drive’s  jumpers, you are ready to install your
DVD-RAM inside your computer.

IMPORTANT: Disconnect power from your computer system before be-
ginning installation.

C

S

S

L

M

A

Summary of Contents for 1202kit















Reviews: