Toro Z500 Series Z Master Operator'S Manual Download Page 42

Page: 42 / 64

the mower belt if any of these conditions are
evident.

1. Disengage the PTO, move the motion control

levers to the neutral locked position, and set
the parking brake.

2. Stop the engine, remove the key, and wait for

all moving parts to stop before leaving the
operating position.

3. Remove the belt covers.

4. Loosen the nut securing the idler plate and

move the idler plate to relieve the belt tension
on the idler pulley (Figure 50).

5. Remove the nut, washer and belt guide from

the rear leftside pulley.

6. Remove the mower belt from the belt guides

and remove the belt (Figure 50).

7. Install the new mower belt around the mower

spindle pulleys, mower idler pulley, into the
belt guides, into rear idler arm assembly, and
the clutch (Figure 50).

8. Install the belt guide with a washer and nut

onto the rear leftside pulley.

Note:

Check the amount of twist in the belt

between the pulleys. Ensure it is only what is
speciﬁed in Figure 50.

Figure 50

1. Clutch

4. Belt guide 7. Belt guide

installed

10. Rear left

side pulley

2. Mower

belt

5. Mower

spindle

pulley

8. Nut

3. 1/4 trun

belt twist

6. Mower

idler

pulley

9. Washer

9. Adjust the belt tension, refer to Adjusting the

Mower Belt Tension

10. Install the belt covers and close the latches

(Figure 51).

Summary of Contents for Z500 Series Z Master

































































Search results

Summary of Contents for Z500 Series Z Master

Reviews:

Related manuals for Z500 Series Z Master

Brands by name

Popular brands

Toro Z500 Series Z Master, Operator'S Manual

Search results

Summary of Contents for Z500 Series Z Master

Reviews:

Related manuals for Z500 Series Z Master

Brands by name

Popular brands