Toro Z500 Series Z Master Operator'S Manual Download Page 38

Page: 38 / 64

Charging the Battery

Charging the battery produces gasses that
can explode.

Never smoke near the battery and keep
sparks and ﬂames away from battery.

Important:

Always keep the battery

fully charged (1.265 speciﬁc gravity). This
is especially important to prevent battery
damage when the temperature is below 32°F
(0°C).

1. Remove the battery from the chassis.

2. Charge battery for 10 to 15 minutes at 25 to 30

amps or 30 minutes at 4-6 amps.

3. When the battery is fully charged, unplug

the charger from the electrical outlet, then
disconnect the charger leads from the battery
posts (Fig. 67).

Figure 41

4. Install the battery in the machine and connect

the battery cables; refer to Installing the
Battery.

Note:

Do not run the machine with the

battery disconnected, electrical damage may
occur.

Servicing the Fuses

The electrical system is protected by fuses. It
requires no maintenance, however, if a fuse blows
check component/circuit for malfunction or short.

The fuses are as follows:

•

Main F1-30 amp, blade-type

•

Alternator F2-25 amp, blade-type

1. Unlatch the seat and raise the seat to gain

access to fuse holder (Figure 42).

Figure 42

1. Main F1-30 amp

2. Alternator F2-25 amp

2. To replace the fuses, pull out on the fuse to

remove it.

3. Install a new fuse (Figure 42).

Summary of Contents for Z500 Series Z Master

































































Search results

Summary of Contents for Z500 Series Z Master

Reviews:

Related manuals for Z500 Series Z Master

Brands by name

Popular brands

Toro Z500 Series Z Master, Operator'S Manual

Search results

Summary of Contents for Z500 Series Z Master

Reviews:

Related manuals for Z500 Series Z Master

Brands by name

Popular brands