Toro Z500 Series Z Master Operator'S Manual Download Page 18

Page: 18 / 64

Figure 8

1. Safe Zone-use the Z Master

here on slopes less than

15 degrees or at areas.

3. Water

2. Use walk behind mower

and/or hand trimmer near

drop-offs and water.

This machine produces sound levels in
excess of 85 dBA at the operators ear and
can cause hearing loss through extended
periods of exposure.

Wear hearing protection when operating
this machine.

Wear protective equipment for your eyes, ears,
feet, and head when using this machine.

Figure 9

1. Warning— wear hearing protection

Operating the Parking

Brake

Always set the parking brake when you stop the
machine or leave it unattended.

Setting the Parking Brake

1. Move the motion control levers (Figure 16) out

to the neutral lock position.

2. Pull up and back on the parking brake lever to

set the parking brake (Figure 10). The parking
brake lever should stay ﬁrmly in the engaged
position.

Parking brake may not hold machine
parked on a slope and could cause
personal injury or property damage.

Do not park on slopes unless wheels are
chocked or blocked

Releasing the Parking Brake

Push forward and down on the parking brake
lever to release the parking brake (Figure 10). The
parking brake is disengaged and the lever will rest
against the brake stop.

Figure 10

1. Parking brake-ON

3. Brake Stop

2. Parking brake-OFF

Starting and Stopping the

Engine

Starting the Engine

1. Sit on the seat and move the motion controls

to neutral locked position.

2. Set the parking brake; refer to Setting the

Parking Brake.

Summary of Contents for Z500 Series Z Master

































































Search results

Summary of Contents for Z500 Series Z Master

Reviews:

Related manuals for Z500 Series Z Master

Brands by name

Popular brands

Toro Z500 Series Z Master, Operator'S Manual

Search results

Summary of Contents for Z500 Series Z Master

Reviews:

Related manuals for Z500 Series Z Master

Brands by name

Popular brands