Toro TimeCutter SW 4200 Operator'S Manual Download Page 33 | Manualshive

Page: 33 / 60

background image

Premaintenance
Procedures

Raising the Seat

Ensure the parking brake is engaged and lift the seat forward.

The following components can be accessed by raising the seat:

•

Serial plate

•

Service decal

•

Seat-adjustment bolts

•

Fuel filter

•

Battery and battery cables

Releasing the Mower-Deck
Curtain

Loosen the 2 bottom bolts of the curtain to gain access to the
top of the mower deck (

Figure 29

).

Figure 29

1.

Bottom bolt

2.

Mower-deck curtain

Raising the Front of the
Machine

If the front of the machine needs to be raised, use the very
front edge as show in

Figure 30

.

Important:

To prevent damage to the steering

mechanism, ensure the very front edge of the machine
is used for jacking points.

Figure 30

33

«
...
31
32
33
34
35
...
»

Summary of Contents for TimeCutter SW 4200





























































Reviews:

No comments

Related manuals for TimeCutter SW 4200

Brand: Gardena Pages: 70

Brand: Gardena Pages: 84

Brand: Gardena Pages: 24

Brand: Gardena Pages: 8

Brand: Gardena Pages: 60

Brand: Yard Machines Pages: 72

Brand: Gardena Pages: 9

Brand: Toro Pages: 56

Brand: Ransomes Pages: 81

Brand: Agri-Fab Pages: 24

COLLECTOR 53 SE COMBI 53 SE COMBI

Brand: Stiga Pages: 2

Brand: Jacobsen Pages: 20

EZ Walk MW1230B

Brand: Maxim Pages: 11

TurboStar 43-4 TH Classic

Brand: Sabo Pages: 61

Brand: Honda Pages: 20

Brand: LawnMaster Pages: 81

Brand: VITO GARDEN Pages: 24

Brand: Kubota Pages: 142

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands