background image

Form No. 3396-366 Rev A

SnowMaster 724 ZXR Snowthrower

Model No. 36001—Serial No. 316000001 and Up

Operator's Manual

WARNING

CALIFORNIA

Proposition 65 Warning

This product contains a chemical or chemicals

known to the State of California to cause cancer,

birth defects, or reproductive harm.

The engine exhaust from this product

contains chemicals known to the State of

California to cause cancer, birth defects,

or other reproductive harm.

Introduction

This machine is intended to be used by residential
homeowners. It is designed for removing snow from
paved surfaces, such as driveways and sidewalks, and
other surfaces for traffic on residential or commercial
properties. It is not designed for removing materials
other than snow, nor is it designed for clearing off gravel
surfaces.

Read this information carefully to learn how to operate and
maintain your machine properly and to avoid injury and
machine damage. You are responsible for operating the
machine properly and safely.

You may contact Toro directly at www.Toro.com for machine
and accessory information, help finding a dealer, or to register
your machine.

Whenever you need service, genuine Toro parts, or additional
information, contact an Authorized Service Dealer or Toro
Customer Service and have the model and serial numbers of
your machine ready.

Figure 1

identifies the location of the

model and serial numbers on the machine. Write the numbers
in the space provided.

Figure 1

1.

Model and serial number location

Model No.

Serial No.

This manual identifies potential hazards and has safety
messages identified by the safety alert symbol (

Figure 2

),

which signals a hazard that may cause serious injury or death
if you do not follow the recommended precautions.

Figure 2

1.

Safety alert symbol

This manual uses 2 words to highlight information.

Important

calls attention to special mechanical information

and

Note

emphasizes general information worthy of special

attention.

For models with stated power, the net power of the engine was
laboratory rated by the engine manufacturer in accordance
with SAE J1940. As configured to meet safety, emission, and
operating requirements, the actual engine horsepower on this
class of snow thrower will be significantly lower.

© 2015—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420

Register at www.Toro.com.

Original Instructions (EN)

Printed in the USA

All Rights Reserved

*3396-366* A

 

Summary of Contents for SnowMaster 724 ZXR 36001





















Reviews: