background image

Product Overview

Figure 7

1.

Auger lever

7.

Discharge chute

2.

Fuel tank cap

8.

Chute deflector

3.

Dipstick

9.

Chute deflector control

4.

Skid

10.

Discharge chute control

5.

Auger

11.

Upper handle

6.

Scraper

Figure 8

1.

Fuel tank cap

4.

Choke

2.

Primer

5.

Recoil starter

3.

Ignition key

Operation

Before Operation

Safety

Use extension cords and receptacles as specified by
the manufacturer for all machines with electric starting
motors.

Do not operate the machine without wearing adequate
winter garments. Avoid loose fitting clothing that can get
caught in moving parts. Wear slip resistant footwear that
will improve footing on slippery surfaces.

Always wear safety glasses or eye shields during operation
or while performing an adjustment or repair to protect
eyes from foreign objects that may be thrown from the
machine.

Thoroughly inspect the area where the machine is to be
used and remove all doormats, sleds, boards, wires, and
other foreign objects.

If a shield, safety device, or decal is damaged, illegible, or
lost, repair or replace it before beginning operation. Also,
tighten any loose fasteners.

DANGER

Gasoline is extremely flammable and explosive. A
fire or explosion from gasoline can burn you and
others.

To prevent a static charge from igniting the
gasoline, place the container and/or machine
on the ground before filling, not in a vehicle or
on an object.

Fill the tank outdoors when the engine is cold.
Wipe up spills.

Do not handle gasoline when smoking or around
an open flame or sparks.

Store gasoline in an approved fuel container, out
of the reach of children.

Do not tip the machine either forward or
backward with fuel in the fuel tank; otherwise,
fuel may leak out of the machine.

Filling the Fuel Tank

Recommended Fuel:

For best results, use only clean, fresh (less than 30 days
old), unleaded gasoline with an octane rating of 87 or
higher ((R+M)/2 rating method).

Ehtanol:

Gasoline with up to 10% ethanol (gasohol)

or 15% MTBE (methyl tertiary butyl ether) by volume
is acceptable. Ethanol and MTBE are not the same.
Gasoline with 15% ethanol (E15) by volume is not
approved for use.

Never

use gasoline that contains more

7

 

Summary of Contents for SnowMaster 724 ZXR 36001





















Reviews: