background image

Figure 2

1.

Safety alert symbol

This manual uses 2 other words to highlight information.

Important

calls attention to special mechanical

information and

Note

emphasizes general information

worthy of special attention.

Contents

Introduction................................................................. 2
Safety ........................................................................... 4

Safe Operating Practices ....................................... 4
Safety and Instructional Decals ............................. 6

Setup............................................................................ 7

1 Remove, Activate and Charge Battery ................. 8
2 Install the Battery............................................... 9
3 Mounting the Hitch to the Debris

Blower............................................................ 10

4 Connecting the Debris Blower to the Tow

Vehicle ........................................................... 10

Product Overview ...................................................... 11

Controls ............................................................. 11

Operation................................................................... 13

Adding Fuel ....................................................... 13
Checking the Engine Oil Level............................ 14
Checking the Tire Pressure ................................. 14
Checking the Torque of the Wheel Lug

Nuts............................................................... 14

Starting and Stopping the Engine ........................ 14
Controller Time Out........................................... 15
Adjusting the Nozzle Direction........................... 15
Operating Tips ................................................... 15

Maintenance............................................................... 17

Recommended Maintenance Schedule(s) ................ 17

Daily Maintenance Checklist............................... 18
Servicing the Air Cleaner .................................... 19
Servicing the Engine Oil ..................................... 20
Synchronize the Remote Transmitter/Control

Module........................................................... 21

Servicing the Spark Plugs.................................... 22
Replacing the Fuel Filter ..................................... 22
Servicing the Fuel Tank ...................................... 23
Cleaning the Engine Screen and the Oil

Cooler ............................................................ 23

Checking the Nozzle Clamp ............................... 23
Adjusting the Belt............................................... 23
Electrical Maintenance ....................................... 24
Waste Disposal ................................................... 24
Storage ............................................................... 24

Schematics ................................................................. 26

3

Summary of Contents for ProForce 44538





























Reviews: