Toro ProForce 44538 Operator'S Manual Download Page 2

Warning

CALIFORNIA

Proposition 65 Warning

The engine exhaust from this product

contains chemicals known to the State of

California to cause cancer, birth defects,

or other reproductive harm.

Important:

This engine is not equipped with a

spark arrester muffler. It is a violation of California
Public Resource Code Section 4442 to use or operate
the engine on any forest-covered, brush-covered, or
grass-covered land. Other states or federal areas
may have similar laws.

Electromagnetic Compatibility
Domestic:

This device complies with FCC rules Part 15.

Operation is subject to the following two conditions: (1) This
device may not cause harmful interference and (2) this device
must accept any interference that may be received, including
interference that may cause undesirable operation.
This equipment generates and uses radio frequency energy and
if not installed and used properly, that is, in strict accordance
with the manufacturer’s instructions, may cause interference to
radio and television reception. It has been type tested and found
to comply with the limits for a FCC Class B computing device in
accordance with the specifications in Subpart J of Part 15 of
FCC Rules, which are designed to provide reasonable protection
against such interference in a residential installation. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following
measures:Reorient the receiving antenna, relocate the remote
control receiver with respect to the radio/TV antenna or plug
the controller into a different outlet so that the controller and
radio/TV are on different branch circuits.If necessary, the user
should consult the dealer or an experienced radio/television
technician for additional suggestions.The user may find the
following booklet prepared by the Federal Communications
Commission helpful: "How to Identify and Resolve Radio-TV
Interference Problems". This booklet is available from the U.S.
Government Printing Office, Washington, DC 20402. Stock No.
004-000-00345-4.

FCC ID: OF7PFB1
IC: 3575A-PFB1

Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must
accept any interference, including interference that may cause
undesired operation of the device.

If a user makes changes or modifications not
expressly approved by the party responsible for
compliance, they could void the user’s authority
to operate the equipment.

This spark ignition system complies with Canadian
ICES-002.

Introduction

Read this information carefully to learn how to operate
and maintain your product properly and to avoid injury
and product damage. You are responsible for operating
the product properly and safely.

You may contact Toro directly at www.Toro.com for
product and accessory information, help finding a
dealer, or to register your product.

Whenever you need service, genuine Toro parts, or
additional information, contact an Authorized Service
Dealer or Toro Customer Service and have the model
and serial numbers of your product ready. Figure 1
identifies the location of the model and serial numbers
on the product. Write the numbers in the space
provided.

Figure 1

1.

Model and serial number location

Model No.

Serial No.

This manual identifies potential hazards and has
safety messages identified by the safety alert symbol
(Figure 2), which signals a hazard that may cause serious
injury or death if you do not follow the recommended
precautions.

© 2008 —The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420

2

Contact us at www.Toro.com.

Printed in the USA.

All Rights Reserved

Summary of Contents for ProForce 44538





























Reviews: