background image

Operation

Fueling the Machine

Fuel tank capacity:

4.1 L (1.0 US gallon)

For best results, use only clean, fresh (less than 30 days
old), unleaded gasoline with an octane rating of 87 or
higher ((R+M)/2 rating method).

Ethanol

: Gasoline with up to 10% ethanol (gasohol)

or 15% MTBE (methyl tertiary butyl ether) by volume
is acceptable. Ethanol and MTBE are not the same.
Gasoline with 15% ethanol (E15) by volume is not
approved for use.

Never use gasoline that contains

more than 10% ethanol by volume

, such as E15

(contains 15% ethanol), E20 (contains 20% ethanol), or
E85 (contains up to 85% ethanol ). Using unapproved
gasoline may cause performance problems and/or engine
damage which may not be covered under warranty.

Do not

use gasoline containing methanol.

Do not

store fuel either in the fuel tank or fuel containers

over the winter unless a fuel stabilizer is used.

Do not

add oil to gasoline.

Important:

Do not use fuel additives other than a fuel

stabilizer/conditioner. Do not use fuel stabilizers with an
alcohol base such as ethanol, methanol, or isopropanol.

DANGER

In certain conditions, gasoline is extremely
flammable and highly explosive. A fire or explosion
from gasoline can burn you and others and can
damage property.

Fill the fuel tank outdoors, in an open area, and
when the engine is cold. Wipe up any gasoline
that spills.

Do not fill the fuel tank completely full. Add
gasoline to the fuel tank until the level is 6 to 13
mm (1/4 to 1/2 inch) below the bottom of the
filler neck. This empty space in the tank allows
the gasoline to expand.

Never smoke when handling gasoline, and stay
away from an open flame or where a spark may
ignite the gasoline fumes.

Store gasoline in an approved fuel container and
keep it out of the reach of children.

Never buy more than a 30-day supply of
gasoline.

DANGER

When fueling, under certain circumstances, a static
charge can develop, igniting the gasoline. A fire or
explosion from gasoline can burn you and others
and damage property.

Always place gasoline containers on the ground
and away from your vehicle before filling.

Do not fill gasoline containers inside a vehicle or
on a truck or trailer bed because interior carpets
or plastic truck bed liners may insulate the
container and slow the loss of any static charge.

When practical, remove gasoline-powered
equipment from the truck or trailer and refuel
the equipment with its wheels on the round.

If this is not possible, then refuel such
equipment on a truck or trailer from a portable
container, not from a gasoline dispenser nozzle.

If you must use a gasoline dispenser nozzle,
keep the nozzle in contact with the rim of the
fuel tank or container opening at all times until
fueling is complete.

Adding Fuel to the Fuel Tank

1.

Clean around the fuel-tank cap (

Figure 7

).

Figure 7

1.

Filler neck

2.

Fuel-tank cap

2.

Remove the cap from the fuel tank (

Figure 7

).

3.

Fill the fuel tank with unleaded gasoline to within 6 to
13 mm (1/4 to 1/2 inch) from the top of the tank.

Do

not fill into the filler neck.

Important:

Do not fill the tank more than 6 mm

(1/4 inch) from the top of the tank because the
gasoline must have room to expand.

4.

Install the fuel-tank cap and wipe up any spilled
gasoline (

Figure 7

).

11

 

Summary of Contents for 38700

































Reviews: