background image

Problem

Possible Cause

Corrective Action

1. The throttle is not in the F

AST

position

when throwing snow.

1. Move the throttle to the F

AST

position.

2. The machine is moving too fast to clear

the snow.

2. Shift the machine into a lower gear.

3. You are trying to remove too much

snow per swath.

3. Reduce the amount of snow removed

per swath.

4. You are trying to remove extremely

heavy or wet snow.

4. Do not overload the machine with

extremely heavy or wet snow.

5. The discharge chute is plugged.

5. Unclog the discharge chute.

6. The auger/impeller drive belt is loose

or is off the pulley.

6. Install and/or adjust the auger/impeller

drive belt; refer to www.Toro.com
for servicing information or take the
machine to an Authorized Service
Dealer.

The engine runs, but the machine
discharges snow poorly or not at all.

7. The auger/impeller drive belt is worn

or broken.

7. Replace the auger/impeller drive belt;

refer to www.Toro.com for servicing
information or take the machine to an
Authorized Service Dealer.

The discharge chute either does not lock
into place or does not move.

1. The discharge-chute latch is not

properly adjusted.

1. Adjust the discharge-chute latch.

1. The skids and/or scraper are not

properly adjusted.

1. Adjust the skids and/or the scraper.

The machine does not properly clear the
snow off the surface.

2. The pressure in the tires is not equal.

2. Check and adjust the pressure in 1 or

both tires.

25

 

Summary of Contents for 37797





























Reviews: