background image

Maintenance

Recommended Maintenance Schedule(s)

Maintenance Service

Interval

Maintenance Procedure

After the first 2 hours

• Inspect the traction cable and adjust it if necessary.
• Inspect the auger/impeller cable and adjust it if necessary.

After the first 5 hours

• Change the engine oil.

Before each use or daily

• Check the engine-oil level and add oil if necessary.

Every 100 hours

• Replace the spark plug.

Yearly

• Check the skids and the scraper and adjust them if necessary.
• Inspect the traction cable and adjust or replace it if necessary.
• Inspect the auger/impeller cable and adjust or replace it if necessary.
• Check the auger-gearbox oil and add oil if necessary.
• Change the engine oil.
• Lubricate the hex shaft.

Yearly or before storage

• Check the air pressure in the tires and inflate them to 116 to 137 kPa (17 to 20 psi).
• Drain the fuel and run the engine to dry out the fuel tank and the carburetor at the

end of the season.

• Have an Authorized Service Dealer inspect and replace the traction-drive belt and/or

the auger/impeller drive belt, if necessary.

Important:

You can find more information about maintaining and servicing your machine at

www.Toro.com.

Maintenance Safety

Read the following safety precautions before
performing any maintenance on the machine:

Before performing any maintenance, service, or
adjustment, shut off the engine and remove the
key. If major repairs are ever needed, contact an
Authorized Service Dealer.

Check all fasteners at frequent intervals for proper
tightness to ensure that the machine is in safe
working condition.

Do not change the governor settings on the engine.

Purchase only genuine Toro replacement parts
and accessories.

Preparing for Maintenance

1.

Move the machine to a level surface.

2.

Shut off the engine and wait for all moving parts
to stop.

3.

Disconnect the spark-plug wire. Refer to

Replacing the Spark Plug (page 20)

.

16

 

Summary of Contents for 37797





























Reviews: