manualshive.com logo in svg

Toro 02000 GROUNDS PRO 2000, Operator'S Manual, Page: 9 / 36

Share
Download
Toro 02000 GROUNDS PRO 2000 Operator'S Manual Download Page 9

Engine: 

Briggs & Stratton Vanguard, twin-cylinder, 4-

cycle, air-cooled, 11.9 kW @ 3600 rpm, 588 cc
displacement, governed speed of 3200 rpm.  Mechanical
fuel pump, large-capacity dual element air cleaner.  2.5 l
oil capacity.

Fuel Capacity:

20 liter.

Traction Drive:

Eaton model 11 hydrostatic transmission

integrally coupled to a Peerless model 1310 axle.  Travel
speed range is 0–13.5 Km/h (0–8.5 mph) forward and
4.8 Km/h reverse (0–3 mph).

Controls:

Foot-operated traction pedal. Hand-operated

throttle, choke, ignition switch, PTO switch, lift lever,
parking brake and seat adjustment.

Cutting Drive: 

Constant-tension belt drive system with

electric clutch utilizing a poly-V belt from the engine to
the jackshaft and BX section V-belt drive from the
jackshaft to each cutting unit.

Tires and Wheels: 

Two 23 x 8.5-12 front-drive turf tires

with 4-ply construction. Rear tires for the four-wheel
configuration, 16 x 6.5-6 turf tires with 4-ply
construction. Rear tire for the three-wheel configuration,
18 x 6.5-8 with 4-ply construction.  83–124 kPa inflation
pressure for all tires.

Electrical Features: 

12-volt, 255 cold cranking amps at

180 C, 50-amp reserve capacity at 270 C.  Battery, 16-
amp alternator, seat, traction, PTO and parking brake
interlock switches; electrical leads provided for optional
light and hour meter installations.

Steering: 

Pinion and gear sector with solid control link

to the rear steer assembly, 2.5 turns lock to lock.

Brakes: 

Service braking accomplished through

hydrostatic transmission. Parking brake controls
secondary shaft internal to the axle assembly and is
actuated by a control lever.

Main Frame: 

All-steel welded construction utilizing

tubular and formed sheet metal sections

Seat: 

Standard cushion seat and optional deluxe

suspension seat with arm rest and weight adjustment.
The seat is adjustable fore and aft.  Arm rest kit also
available.

Lift System:

Category “0” A-Frame mounting system

connected to the tractor via parallel linkage. One double-
acting 60 mm bore, 140-mm stroke hydraulic cylinder
receiving oil from hydrostatic transmission charge pump
via the control valve with float position. Maximum
operating pressure is 6895 kPa.  When the traction unit is
equipped with cutting units, all three units are raised and
lowered via the single control lever. The lift system
works with the electric clutch to engage and disengage
the cutting units.

Overall Dimensions and Weight:

Wheel Tread Width

105.3 cm

Width across Front Tires

132 cm

Wheel Base

138.5 cm

Overall Length w/ Cutting Units Installed

229 cm

Overall Height

119 cm

Tractor Weight

50.4 kg

Weight with 5-Blade Fixed Cutting Units

440 kg

Weight with 8-Blade Floating Cutting Units

696 kg

Overall Width w/Fixed-Head Units

195 cm

Overall Width w/Floating Head Units

203 cm

Transport Width w/Fixed Head Units

140 cm

Transport Width w/Floating Head Units

200 cm

Optional Equipment:

Fixed Head Kit 

Model No. 02100

Floating Head Kit 

Model No. 02101

3-Wheel Axle 

Model No. 02200

4-Wheel Axle 

Model No. 02201

Full Roller Kit*

Model No. 03440

Sectional Roller Kit* 

Model No. 03445

Wiehle Roller Kit* 

Model No. 03450

Skid Kit* 

Model No. 03446

Anti-Scalp Kit* 

Model No. 03447

Grass Basket Kit 

Model No. 02302

Power Take-off Kit 

Model No. 02301

Standard Seat Kit 

Model No. 30769

Deluxe Seat Kit 

Model No. 30772

Arm Rest Kit 

Model No. 30707

Roller Scraper Kit* 

Part No. 60-9560

Comb Kit* 

Part No. 67-9400

Rear Weight 

Part No. 24-5790

9

Specifications

Summary of Contents for 02000 GROUNDS PRO 2000





































Reviews:

No comments