manualshive.com logo in svg

Tornatech GLU, Installation And Maintenance Manual, Page: 55 / 61

Share
Download
Tornatech GLU Installation And Maintenance Manual Download Page 55

 

 

55 

 

Pump Curves 

History > Pump Curves 

 

The vertical axis represents the pressure in the actual unit selected. Its scale is dynamic and will resize depending 
on the highest recorded value. The horizontal axis represents the flow in the actual unit selected. Its scale is 
dynamic and will resize depending on the highest recorded value. The contextual navigation pad is implemented in 
this page. It allows quick navigations functions, like “Previous” and “Next”. As always, clicking on the Navigation 
Pad Icon in the lower right corner of the screen will activate the Navigation Pad with functions specific to that page. 
By pressing the right or left buttons on the navigation pad, the pump curve displayed will change, allowing a quick 
user-friendly navigation. 
 
The navigation is also represented in the elements of the upper right corner of the graph. The white square 
indicates the date and time when the pump curve was recorded. The two arrow buttons will select the next or the 
previous pump curve and the “Delete” button will delete the currently selected pump curve, if the user is at least 
logged in as “Level 1”. 
 

Summary of Contents for GLU






























































Reviews:

No comments