manualshive.com logo in svg

Tornatech GLU, Installation And Maintenance Manual, Page: 47 / 61

Share
Download
Tornatech GLU Installation And Maintenance Manual Download Page 47

 

 

47 

 

 

History (Membrane button) 

History 

 

Select specific pages within the History section. Everything related to the statistics, events, pressure, power logs 
and the download to USB is available within the History page. 
 
-

Events: This button leads to the “Events” page, which displays the most recent 500 events. Each event log 

contains the date and time of occurrence as well as a brief description of the event. 
 
-

Download to USB Device: This button leads to the “Download to USB Device” page, which allows the user to 

download information, including the user manual, drawings, logs, statistics and configuration. 
  
-

First Service Statistics: This button leads to the “First Service Statistics” page, which displays all relevant statistics 

calculated since the very first service done on the controller. 
 
-Last Service Statist

ics: This button leads to the “Last Service Statistics” page, which displays all relevant statistics 

calculated since the last service done on the controller. 
 
-

All Time Statistics: This button leads to the “All Time Statistics” page, which displays the date and time of the first 

power up, the date and time when the first start-

up was completed and the total “On Time” of the controller. These 

statistics can never be reset. 
 
-

Pressure/Power Curves: This button leads to the “Pressure Curves” / “Power Curves” page accordingly, which 

displays all relevant pressure/power information. 
 
-

Pump Curves: This button leads to the “Pump Curves” page. 

 
 

History 

Summary of Contents for GLU






























































Reviews:

No comments