manualshive.com logo in svg

Tornatech GLU, Installation And Maintenance Manual, Page: 35 / 61

Share
Download
Tornatech GLU Installation And Maintenance Manual Download Page 35

 

 

35 

 

Factory Settings 

Config > Advanced > TS Factory Settings 

 

 

The factory settings are always pre-configured at the factory and set the main parameters of the controller. Most of 
the settings found on this page can only be changed by an authorized Tornatech employee and is protected by a 
level 8 password. 
 
Normal Dropout Voltage: Percentage of nominal voltage under which the normal power source will be disqualified 
(after expiration of the normal outage delay). 
 
Normal pickup voltage: Percentage of nominal voltage above which the normal power source will be re-qualified 
(after expiration of the retransfer time - see page 67). 
 
Normal outage: Delay after which the normal power can be disqualified only if the voltage has been all the time 
during this delay below the Normal Dropout Voltage. 
 
Alternate dropout voltage: Percentage of nominal voltage under which the alternate power source will be 
disqualified. 
 
Alternate pickup voltage: Percentage of alternate voltage above which the normal power source will be qualified 
(after expiration of the alternate available delay). 
 
Alternate available delay: Delay after which the alternate power source can be qualified. 
 

Summary of Contents for GLU






























































Reviews:

No comments