manualshive.com logo in svg

Tornatech GLU, Installation And Maintenance Manual, Page: 46 / 61

Share
Download
Tornatech GLU Installation And Maintenance Manual Download Page 46

 

 

46 

 

 

These pages allow to configure the Lockout input and the interlock output parameters. To be active, those options 
need to be assigned to an Input or an Output on the I/O board. 
 
Lockout is an Input that disables the motor from starting. 
- Enable in emergency: If checked, this option will prevent the electronic assistance on an Emergency start. 
- Enable in manual mode: If checked, this option will prevent the Manual start. 
- Enable in automatic mode: If checked, this option will prevent the Automatic start. 
- Enable in remote manual mode: If checked, this option will prevent the Remote Manual start. 
- Enable in "start/stop" mode: If checked, this option will prevent the "start/stop" mode. 
- Shutdown Motor: If enabled, the lockout signal will also act as a shutdown and will stop the motor if it is running. 
 
Interlock is an Output that prevents a second motor from starting. 
- Enable in emergency: If checked, this option will activate the output "interlock" on an Emergency start. 
- Enable in manual mode: If checked, this option will activate the output "interlock" on a Manual start. 
- Enable in automatic: If checked, this option will activate the output "interlock" on a Automatic start. 
- Enable in Remote Manual mode: If checked, this option will activate the output "interlock" on a Remote Manual 
start. 
- Enable in "start/stop" mode: If checked, this option will activate the output "interlock" on a "start/stop" mode. 
- Main Coil required: If enabled, the controller will wait to have the Main Coil signal active before activating the 
Interlock output. 
 

Summary of Contents for GLU






























































Reviews:

No comments