background image

5

IMPORTANT SAFETY INSTRUCTIONS

14. CAUTION –If it is suspected that there is hazardous dust or flammable/corrosive 

material, stop cleaning the area immediately and consult your supervisor.

15. DO NOT use to clean up any burning or lighted materials such as cigarettes, 

matches, ashes, or other combustible objects. 

16. Only use the machine on firm, level surfaces. DO NOT use the machine on 

gradient or slope of more that 2%.

17. CAUTION –This machine is for dry, indoor use only and should not be used or 

stored outdoors or in wet conditions. Protect from rain.

18. Take care when using this machine near the top of stairs to avoid loss of 

balance.

19. DO NOT cover the machine when in use.

20. DO NOT run the machine dry as this could damage the pump.

21. DO NOT leave the machine running unattended.

22. Keep hair, loose clothing, hands, feet, and all other parts of the body away from 

openings and moving parts. Do not put hands under base as rotating parts can 

cause injury.

23. DO NOT put any object into openings. DO NOT use with any opening blocked. 

Keep free of dust, debris and anything that may reduce airflow.

24. DO NOT use volatile or combustible solvents (e.g., diesel, petrol, PA, 

trichloromethane) nor any corrosive, toxic, or highly irritant substance to wash 

floors, even if diluted. In the event of accidental contact with any such substances 

(e.g., due to spills) follow the decontamination procedures in force at the user site. 

If in any doubt about the condition of the machine, contact Tornado or the dealer/

agent who supplied the machine.

25. DO NOT leave the machine unattended when plugged in. Unplug from outlet 

when not in use and before attempting any maintenance or adjustment.

26. DO NOT fill the machine with water hotter than 140°F (62°C).

27. When used on escalators, ensure the machine is positioned at the bottom of 

the escalator with the escalator moving towards the operator.

28. DO NOT pull or carry by cord, use cord as a handle, close a door on cord, or 

pull cord around sharp edges on corners.

29. DO NOT run machine over cord. Keep cord away from heated surfaces.

30. DO NOT unplug by pulling on cord. To unplug, grasp the plug, not the cord. Do 

not handle plug or machine with wet hands. Turn off all controls before unplugging.

31. Connect only to a properly grounded outlet. See grounding instructions.

32. Use care to keep electrical supply cable from contacting moving parts.

33. Make sure voltage and frequency at the wall receptacle correspond with that 

indicated on nameplate before plugging in machine.

34. The machine must be kept clean and in good condition with regular inspections 

of the power cord and plug for signs of any damage. If any parts are damaged, they 

shall only be replaced by an approved part by the manufacturer, its service agent or 

a similar qualified person in order to avoid a hazard.

35. Only replace the power cord with original OEM equipment.

36. Do not use the machine for totally dry vacuuming.  This machine is not fitted 

with a fine dust filter.

Summary of Contents for TE010-G003-U




















Reviews: