background image

12

Warning!

 Switch off the machine and unplug from the electrical supply before performing any cleaning 

operations.

(viii)

3

2

1

(ix)

(x)

(xi)

1.  Move the Transport / Working mode control knob to BOTTOM 

(Transport) position to move the brushes off of the floor (Fig-viii).

2.  Unplug the machine and wrap the supply cord around the hooks on 

the handle.

3.  Pull out the dirty water tank and wash it completely.
4.  To prevent possible clogging of the solution lines in the solution tank, 

empty any unused solution from the tank and filter, drain cleaning 

liquid, and keep the fresh water tank clean. 

5.  Remove the brushes by pushing the brush shaft out (Fig-ix).
6.  Wash the brushes either by dipping in a bucket/sink or in running 

water (Fig-x).

7.  Turn the machine on its side and wipe clean the rubberized drum and 

machine body with a damp cloth (Fig-xi).

8.  Re-install the brushes after washing. It is easier to push the brush 

shaft from the right hand side (identified by the electrical cable).

9.  Store the machine in a dry indoor area only.

Warning!

 Before undertaking any maintenance operations or adjustments, switch off the 

machine and unplug from the electrical supply.

(viii)

3

2

1

(ix)

(x)

(xi)

(viii)

3

2

1

(ix)

(x)

(xi)

(viii)

3

2

1

(ix)

(x)

(xi)

Cleaning the Machine

Maintenance

To get the maximum life of the machine, do the following:
•  Supply Cord
Regularly inspect sheath, plug and cord anchorage for damage or loose connection. Replaced if
damaged.
•  Brushes
Wash the brushes regularly. Make sure that the machine is in Transport Mode when not in use.
Store additional brushes in a vertical position to avoid bending the bristles. Check for permanent
bending of bristles in a particular direction. This may occur if the machine is operated for several 
days without removing the brushes, which is not recommended. If this occurs, reverse the brush 
so that the bent bristles are straightened.
•  Wiper Blade
If the wiper blade wears out, the water collection performance will decrease. It should be 
replaced by an authorized service agent.
•  Solution Feed Filter (Pump)
The filter should be periodically cleaned. Use pressurized air/water for cleaning.
•  Nozzle Maintenance (Pump)
If the spray nozzle is blocked, slide the nozzle cover off and remove the nozzle. Clean it with  
clean water and use a pin to unclog, then reinstall.

Summary of Contents for 99409
















Reviews: