background image

 

17 

 

322 Railroad Ave North, Kent, WA 98032

 

Phone (800) 246-8132 Fax (253) 854-8003 

 

or visit our website: 

www.TorkLift.com

 

 

Dear Valued Customer,  
 
Thank you for making TorkLift your choice for truck, camper packages and accessories 
for your vehicle. By choosing TorkLift products, you have chosen a company that has 
been serving the RV industry for nearly 40 years and whose name has become 
synonymous with strength, quality and advanced design and installation.  
 
Please take a few moments of your time to complete the Product Registration 
Warranty Card on the next page. When registering your newly purchased TorkLift 
products, you can be assured that your contact information is secure and that you and 
your product are getting the attention and respect that you deserve.  
 
Thank you again for choosing TorkLift quality products. 

Register for your lifetime warranty and receive a free Torklift  

International gift. 

To Fax: Send copies of the questionnaire, warranty card and receipt to 

253-854-8003 

To E-mail: Send copies of the questionnaire, warranty card and receipt to 

[email protected] 

To Mail: Send to Torklift International 

322 Railroad Ave North, Kent, WA 98032 

 

Summary of Contents for D3109



















Reviews: