Torklift A7720R Important Owner-Operator Installation Instructions Download Page 14

13 

 

Torklift International Limited Lifetime 

Warranty Information 

 

1901 Fryar Ave Sumner, WA 98390 

 

Torklift will require proof of purchase to register, with pictures of any 
defective product before issuing a replacement. Torklift will not register 
any product without proof of purchase, which can be faxed, scanned, 
emailed, or mailed to the information provided below. Torklift warrants 
its hitches, custom hitch receivers, frame mounted tie downs, 
turnbuckles, and accessories (excluding wire harnesses which carry a 90 
day warranty) from date of purchase against defects in material and 
workmanship under normal use and service for the ownership life of the 
original consumer purchaser. All plastic, rubber, and/ or electrical 
components maintain a warranty of up to one year from the date of the 
purchase. ALL COMMERCIAL APPLICATIONS ARE WARRANTED 
FOR A PERIOD OF 90 DAYS FROM THE DATE OF 
INSTALLATION/SERVICE. Torklift will replace FREE OF CHARGE 
any part which proves defective in material or workmanship when 
presented to Torklift, TRANSPORTATION CHARGES PREPAID by 
purchaser, at the address above. THIS WARRANTY IS LIMITED TO 
DEFECTIVE PARTS REPLACEMENT ONLY. LABOR CHARGES 
AND/OR DAMAGE INCURRED IN INSTALLATION OR 
REPLACEMENT, AS WELL AS INCIDENTAL AND 
CONSEQUENTIAL DAMAGES CONNECTED THEREWITH ARE 
EXCLUDED. This warranty does not include the finish or paint on our 
products. Rusting, cracking or peeling of the finish is also excluded. 
Some states do not allow the exclusion or limitation of incidental or 
consequential damages, so the above limitation or exclusion may not 
apply to you. Any damage to Torklift products as a result of misuse, 
abuse, neglect, accident, improper installation or any use violative of 
instructions furnished by Torklift or WHEN USED IN ANY 
COMMERCIAL APPLICATION WILL VOID THE WARRANTY. 
This warranty gives you specific legal rights, and you may also have 
rights which vary from state to state. With warranty service, you may be 
able to go to a small claims court, a state court or a federal district court. 

 

Summary of Contents for A7720R

















Reviews: