background image

MAINTENANCE

Topray Solar crystalline solar modules require minimal maintenance. Given a sufficient tilt (at least 15°), it is not generally 

necessary to clean the modules (rainfall will have a self cleaning effect). Regular maintenance is required to keep modules 

clear of snow, bird droppings, seeds, pollen, leaves, branches, dust and dirt spots. When there is a noticeable buildup of 

soiling deposits on the module surface, wash the PV array using water without cleaning agents and a gentle cleaning 

implement (a sponge), during the cool of the day. Dirt must never be scraped or rubbed away when dry, as this will cause 

micro-scratches. If snow is present, a brush with soft bristles can be used to clean the surface of the module. 

Once a year the modules need to be inspected for tightness of screws securing the modules to the racking frame. The 

general condition of the wiring needs to also be inspected. Loose hardware could result in damage to the panel. Strong 

wind conditions could loosen the mounting devices. 

Do not change the PV components (diode, junction box, plug connectors). 

If you need electrical or mechanical inspection or maintenance, it is recommended to have a licensed, authorized 

professional carry out the inspection or maintenance to avoid hazards of electric shock or injury. 

WARNING:Foranyelectricalmaintenance,thePVsystemmustfirstbeshutdown.Impropermaintenancecancause

lethalelectricshockand/orburns.

OWNERSHIP

This manual is the proprietary property of Topray Solar Co., Ltd. No part of this manual may be reproduced or copied 

without the express written permission of Topray Solar Co., Ltd. Any unauthorized use of this manual or its contents is 

strictly prohibited. No license is granted by implication or under any patent or patent rights. Any and all intellectual 

property rights in or related to the PV modules are and shall remain the property of Topray Solar Co., Ltd. All rights are 

expressly reserved. 

DISCLAIMEROFLIABILITY

The installation techniques, handling and use of Topray Solar crystalline solar modules are beyond company control. 

Therefore Topray Solar does not accept responsibility and expressly disclaims liability for any loss, damage, or expense 

arising out of or in any way connected with such installation, operation, use or maintenance. 

Topray Solar bears no responsibilities for any infringement of rights of third parties that may result from the use of the 

module. No license is granted by implication or under any patent or patent rights.  

The information in this manual is based on Topray Solar’s best knowledge and experience and is believed to be reliable; 

but such information including product specification (without limitations) and suggestions do not constitute a warranty, 

express or implied. Topray Solar reserves the right to change the manual, the PV produce, the specifications, or product 

information sheets without prior notice.  

15

Summary of Contents for TPSM5U



















Reviews: