Topfloor TF90VB-TRS Operator'S Manual Download Page 5

 

 

TF90-TRS 

 

Introduction 

This operating manual contains instructions for using the hand-operated 
sweeper.  

Our products are subject to continuous improvement. Therefore, design 
changes that were made after this manual went to print could not be 
incorporated. If you have any questions, please contact our Service 
department. 

The operating manual must be read and applied by all persons who 
operate the sweeper. 

Apart from the operating manual and the regulations for accident pre-
vention applicable in the country of use and the location of use, the 
common, recognised rules for safe and technically correct working must 
also be followed. 

 

1.1 

Usage conformant with intended purpose 

The appliance is intended exclusively for sweeping on solid surfaces (for 
example: parking areas, walkways, shop floors). The area to be swept 
should not be wet. 

The sweeper may only be used by reliable and instructed personnel. 
Prevent children, juveniles and other unauthorised persons from using 
the machine (e.g. by pulling out the key after use). 

Any other use, or any use over and above that, will be considered to be 
non-conformant with intended purpose. The manufacturer rejects any 
and all liability for damage resulting from such use. The risk is that of the 
user alone. 

Usage conformant with intended purpose also includes compliance with 
the operating manual and the inspection and maintenance specifica-
tions. Drive the sweeper only along expressly marked routes and spac-
es.  

 

Summary of Contents for TF90VB-TRS

























Reviews: