23
the pushrods into the holes
. Then, use medium CA to
glue the pushrods in.
❏
❏
4.
Fit the replica engine in the co
wl and align the
tw
o missing cylinders with the cutout f
o
r the engine
.
Le
v
e
l the replica engine inside the front of the co
wl,
doub
le-chec
k the alignment, and then use thin CA
to carefully glue the replica engine into position.
Use
care not to use too m
uch CA which could r
un onto the
outside of the co
wl.
❏
❏
5.
If necessar
y,
cut a hole in the top of the
replica engine in alignment with the slot in the top of
the co
wl f
o
r the 3/32" Allen wrench.
❏
❏
6.
T
a
k
e
the dr
iv
e w
a
sher off the engine
. If
necessar
y,
enlarge the hole in the front of the replica
engine so the co
wl will go o
v
er the engine
. Mount
the co
wl to the nacelle and put the dr
iv
e w
a
sher
bac
k on.
If y
ou pref
er not to remo
v
e
the dr
iv
e w
a
sher
fo
r installing the co
wl, the hole in the middle of the
replica engine will ha
v
e
to be enlarged e
v
en more
.
Similar
ly
, if y
ou install the v
a
lv
e co
v
e
r on the engine
after y
ou install the co
wl, the hole in the co
wl f
o
r the
engine can remain small.
❏
7.
Mount the other replica engine in the other co
wl
the same w
a
y.
HOOK UP
THE FLAPS AND AILER
ONS
❏
1.
Retr
ie
v
e y
o
ur fl
ap and aileron ser
v
o
s
. Center
each ser
v
o
b
y
connecting it to the receiv
e
r,
center
ing
the tr
ims on the tr
ansmitter
, and then tur
n
ing on the
tr
ansmitter and receiv
e
r.
Once y
ou fi
nd the ser
v
o
ar
m
that’
s
90-deg
rees
, cut off the rest.
❏
2.
Mount the ser
v
o
s to the mounting b
loc
ks on each
of the six hatches b
y
using the holes in the ser
v
o
s as
guides f
o
r dr
illing 1/16" [1.6mm] holes into the ser
v
o
b
loc
ks
. T
empor
ar
ily mount the ser
v
o
s with the scre
w
s
that came with them, remo
v
e
the scre
ws and ser
v
o
s
,
and then harden each hole with a f
e
w drops of thin CA.
Allo
w the CA to harden.
Then, remount the ser
v
o
s
.
6" [150 mm]
SER
V
O
EXTENSION
❏
3.
Connect a 6" [150mm] ser
v
o
e
x
tension to
each aileron ser
v
o
. (Ref
er to the
“Ser
v
o
Extensions”
sk
etches in the bac
k of the man
ual f
o
r full diag
ra
ms
of what ser
v
o
e
x
tensions and
Y
-har
nesses are used.)
Same as the throttle ser
v
o
s
, secure the connection
with 1-1/2" [40mm] pieces of heat shr
ink tubing.
The hatches ha
v
e
been
enlarged f
o
r clar
ity
.
LEFT WING
RIGHT WING
❏
4.
Noting the or
ientation of the ser
vo
hatches in the
bottom of the wing, place the ser
vo
hatches with the
ser
vos in the respectiv
e wing panels—be cer
tain the
scre
ws that hold on the ser
vo
ar
ms are in all the ser
vo
s!
Use the str
ings in the wings to guide the ser
vo
wires
out the ends of the panels—or just drop them do
wn
through the holes while holding the wings on-end.
❏
5.
Prepare f
o
r making the fl
ap and aileron pushrods
b
y
reading the f
o
llo
wing
“Hot Tip”
on ho
w to solder
.
Then, gather y
our solder
ing equipment.
