background image

4

8.2 Insert / remove hot glue stick

8.2.1 Insert

P

RECONDITIONS

:

a

The power is switched OFF (0).

a

The battery is disconnected.

1. Insert a hot glue stick into the inlet.
2. Gently push the stick through the opening until it will go no further.

8.2.2 Remove

Important:

Risk of damage. Do not try to remove any unused portions of the glue stick after use.

If you need to change the glue type:

Cut off any glue protruding from inlet.

Gently squeeze the remaining glue through the nozzle until the new glue stick behind it flows through.

8.3 Gluing

If the glue stick does not enter the inlet easily, DO NOT keep squeezing the trigger. The
glue chamber may not be hot enough to melt the glue. Refer to section “Gluing” for fur-
ther information.

Risk of severe burns! Excessive squeezing of the trigger may cause hot glue to reverse
out of the inlet.

Risk of fire and/or burns! Always place the product so the nozzle does not come contact
anything while it is heating or not in use.

Always use safety glasses. Following this rule will reduce the risk of eye injury.

Important:

Always practice gluing on scrap work pieces before final gluing on projects.

Auto shut OFF: The product will automatically power OFF after 10 minutes of continuous
use. Switch the power OFF (0) then ON (I) again to resume use.

P

RECONDITIONS

:

a

Hot glue stick is inserted.

a

Battery is connected.

a

The power is switched OFF (0).

1. Switch the power ON (I).

Heating status indicator:
- RED: heating up.
- GREEN: heated to working temperature.

2. Gently squeeze the feed trigger a few times until adhesive flows from the nozzle.

à

If using the glue gun for the first time or the hot melt chamber is empty, you may use up one stick
before glue flows out.

à

If liquid glue does not appear, wait an additional 1 minute for the heating element to reach a
higher temperature.

3. Switch the power OFF (0) when finished using. Place the product on a protective surface e.g. thick

paper. This is to catch adhesive drips as the product cools down.

4. Allow the adhesive and nozzle to completely cool down before removing the battery pack.

8.4 Gluing tips

The bonding surfaces should be dry, free of dust and grease. Do not use flammable detergents and
solvents.

Zigzag lines of glue are good for adhering flexible materials (e.g. textiles).

Beads of glue are good for adhering all other materials.

The bonding time is approximately 30 seconds and about 90 % of adhesion occurs after one minute.
The bonding time for thick beads of glue can be longer than for small beads.

Do not glue large areas at once, work in sections, and apply the adhesive in a corrugated pattern.

Improve adhesion by preheating surfaces e.g. with a hot air gun.

Only attempt remove adhesive residue when it has completely cooled down.

Loosen or adjust glued areas by heating them, e.g. with a hot air gun.

To glue different materials together, apply adhesive to the harder material.

9 Maintenance and storage

9.1 Maintenance

Important:

The product is generally maintenance-free. Any repair or maintenance work must be carried
out by a specialist.

Important:

– Do not use aggressive cleaning agents, rubbing alcohol or other chemical solutions. They damage

the housing and can cause the product to malfunction.

– Do not immerse the product in water.

1. Switch the power OFF (0).
2. Let the product cool down to ambient temperature.
3. Remove the battery pack.
4. Clean the product with a dry, fibre-free cloth.

9.2 Storage

Important:

Risk of fire and/or injury! Storing this product while hot can cause serious burns and/or ignite
combustible objects.

Before storage:

Always switch the power OFF (0), then remove the battery.

Make sure the product has completely cooled (approximately 30 minutes of cool-down time).

10 Disposal

Electronic devices are recyclable waste and must not be disposed of in the household waste.
At the end of its service life, dispose of the product in accordance with applicable regulatory
guidelines.

Remove any inserted (rechargeable) batteries and dispose of them separately from the
product. You as the end user are required by law (Battery Ordinance) to return all used (re-
chargeable) batteries. Disposing of them in the household waste is prohibited.
Contaminated (rechargeable) batteries are labeled with this symbol to indicate that disposal
in the domestic waste is forbidden. The designations for the heavy metals involved are: Cd =
Cadmium, Hg = Mercury, Pb = Lead (name on (rechargeable) batteries, e.g. below the trash
icon on the left).

You thus fulfill your statutory obligations and contribute to the protection of the environment.

11 Technical data

11.1 Product

Power supply  ........................................

20 V Li-ion (rechargeable battery)

Protection class .....................................

III

Heating time ..........................................

approx. 180 sec

Melting temperature...............................

approx. 170 °C

Gluing capacity ......................................

approx. 15 g/min

Auto shut off ..........................................

10 mins

Operating/storage conditions.................

+10 to +35°C, 20 – 90 % RH (non-condensing)

Dimensions (W x H x D) (approx.) ........

192 x 190 x 68 mm

Weight (approx.)  ...................................

353 g

11.2 Hot glue stick

Dimensions (ø x H)................................

11 x 150 mm

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).

All rights including translation reserved. Reproduction by any method (e.g. photocopying, microfilming or the capture in
electronic data processing systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited.
This publication reflects the technical status at the time of printing.

Copyright by Conrad Electronic SE.

*2388639_V1_1021_dh_mh_en

I1/O1

Summary of Contents for 2388639

Page 1: ...tehen oder Anweisungen hinsichtlich der siche ren Verwendung des Geräts erhalten haben und die damit verbundenen Gefahren kennen Reinigung und Benutzer wartung dürfen von Kindern nur unter Aufsicht durchge führt werden Kinder dürfen mit diesem Produkt nicht spielen Das Produkt ist kein Spielzeug Halten Sie es von Kindern und Haustieren fern Lassen Sie Verpackungsmaterial nicht achtlos herumliegen ...

Page 2: ...terialien z B Textili en Kleberaupen eignen sich für das Verkleben aller anderen Materialien Die Klebezeit beträgt ca 30 Sekunden und ca 90 der Klebkraft ist nach einer Minute erreicht Bei dicken Kleberaupen kann die Klebezeit länger sein als bei kleinen Raupen Kleben Sie keine großen Flächen auf einmal sondern arbeiten Sie abschnittsweise und tragen Sie den Klebstoff wellenförmig auf Verbessern S...

Page 3: ...terial lying around carelessly This may become dangerous playing mater ial for children If you have questions which remain unanswered by this information product contact our technical support service or other technical personnel Maintenance modifications and repairs must only be completed by a technician or an authorised re pair centre 6 2 Handling Handle the product carefully Jolts impacts or a f...

Page 4: ...dhesion by preheating surfaces e g with a hot air gun Only attempt remove adhesive residue when it has completely cooled down Loosen or adjust glued areas by heating them e g with a hot air gun To glue different materials together apply adhesive to the harder material 9 Maintenance and storage 9 1 Maintenance Important The product is generally maintenance free Any repair or maintenance work must b...

Reviews: