background image

 

 

1.3.

 

Safe distances: 

 

Safe distance A 

Sides and rear panels require a minimum distance of 10 cm to inflammable 
materials 

Safe distance B 

The national and local rules and regulations  
 are to observe 

Safe distance C+D 

The entire turning range requires 
a minimum distance of 50 cm 

Safe distance E 

The entire turning range requires 
a minimum distance of 80cm 

Safe distance F 

The minimum distance to the ceiling 
is 50 cm 

 

1.4.

 

Spark protection plate: 

Flammable floor coverings in front of the stove must be protected by a non-
flammable covering. Plates made of stone, ceramic, sheet metal or Securit 
glass  are  suitable  for  this.  Flammable  floors  in  front  of  the  stove  (carpet, 
parquet, plastic) must be covered over. Building regulations, state building 
ordinances and fire protection laws differ from country to country. Enquire to 
the  authority  or  chimney  sweep  responsible  for  the  acceptance  before 
installing. 

 

 

 

CAUTION

 

 

 

CAUTION 
Fire prevention laws stipulate minimum or safe distances for 
inflammable materials (wood panels, panelling, fabrics, etc.). 

These are 

given by the table below: 

Summary of Contents for T-Art eco2



















Reviews: