background image

 

 

PREPARING THE LAND FOR THE INSTALLATION  

 
The area has to be COMPLETELY HORIZONTAL; there can be no unevenness in the land. VERY IMPORTANT: Never install the 
swimming pool on top of expanded polystyrene plaques or similar. Use gloves and glasses during the installation.  

 

Prepare the area, previous to installation, as specified in the following segment:  
 
To  mark the area where the pool is going to be located you will need: A peg or stick, a rope, a funnel (or bottle) and lime, flour or 
similar. For better safety, use gloves and glasses.  
 

If you need to level the area or floor, do not refill the gaps. You have to remove soil from the more elevated areas of the 
floor,  to  level  them  with  the  lower  areas  (and  never  the  other  way  around),  fig  1A.  in  any  case,  you  will  need  to  remove 
roots, stones, grass and sharp objects.  
 

With the help of a rake or board and a level, you will need to level off the ground and cover the gaps with sand.  
 

With the help of a level and a strip of wood, check periodically that the ground is 100% leveled. Level the whole area at the 
same level as the lowest area, fig 2.  

                   

 

       

fig. 1

 

 

 

 

 

 

fig. 2

             

 

Space required fig. 2: 

 

Swimming pool: 550 x 366 x 132 - excavation: (X) length 610 x 518 width (Y) 
Swimming pool: 640 x 366 x 132 - excavation: (X) length 700 x 518 width (Y) 
Swimming pool: 730 x 366 x 132 - excavation: (X) length 790 x 518 width (Y) 
Swimming pool: 915 x 457 x 132 - excavation: (X) length 975 x 610 width (Y) 

 

COMPONENTS 

 

Take out and classify all of the components of the swimming pool before starting the installation, if there is any components missing 
within  the  assembly  kit,  you  need  to  inform  the  after-sales  service  within  15  days  after  the  purchase  of  the  pool,  otherwise  the 
guarantee will not cover this.  

 

ASSEMBLY OF THE CENTRAL PILLAR 

 

PRIOR TO THE ASSEMBLY 

 Very important: 

Always use gloves to work. The installation must be done between at least 2 people.

  

a)  Place  the  short  U  profile  (5),  with  the  open  sides  heading  upwards,  to  continue,  slide 

the  long  U  profile  (4)  on  top  of  the  short  profile,  with  the  open  sides  heading 
downwards,  in  order  to  form  a  sort  of  box,  make  sure  that  the  holes  on  both  profiles 
match, but do not screw them, fig.3.  
 

b)  Now situate the central pillar or column (3) on top of the two profiles, as shown on  

            fig. 4. 

 

c)  Situate the reinforcement plates (both right and left) (12)(13) at each side of the central 

pillar (3) as shown on fig. 5, the reinforcement plates have to be situated under the U 
profiles, use 3 screws (8) to hold the reinforcement plates. 
 

d)  All  holes  have  to  match  in  order  to  situate  the  8  mm  x12  cm  Screws  and  the  8  mm 

nuts(11).  Make  sure  that  the  reinforcement  (14)  is  situated  on  both  sides  of  the 
ensemble. Use the 8mm x11cm screws and 8mm nuts  (15) to attach the upper side of 
the reinforcement plates of the pillars (12) (13), fig.6.  
 

e) 

Once we have tightened all of the screws without forcing them, we have to situate the 
guide  rail  connector  (6)  with  one  single  screw  (9),  as  seen  in  fig.  7.  We  call  each  of 
these groups of united elements: modules

 

 

 

fig. 3 

 

Summary of Contents for Ovalda Ibiza Series






















Reviews: