background image

49-85/86/87 

Rev.E 

 

Available Accessories: 

For Models 49-85 and 49-86: 

 

 

 

 

TMI # 35-12-02 Gauge Blocks for accurate calibration 
(.010 in./.254mm, .020 in./.508mm, .030 in./.762mm, .040 in./1.016mm 
and .050 in./1.270mm in thickness) 
 

For Models 49-87: 

TMI # 35-12-03 Gauge Blocks for accurate calibration 
(0.010 in./.254mm, .100 in./2.54mm, .200 in./5.08mm,  
.300 in./7.62mm, .400 in./10.16mm and .500 in./12.70mm in thickness) 

 

STANDARDS 
 

TAPPI T 411, ISO 534, DIN 53105, ISO 3034, APPITA 1301.426, PAPTAC D.4, ISO 12625-3, 
ISO 037, ASTM F2251, ISO 5084 

 

NOTE: Only the 49-8X configured with the appropriate pressure foot and dead weight is capable 
of meeting above standards 

 

LIST OF EQUIPMENT 

 

x

 

1 TMI Digital Micrometer 

x

 

1 Instruction Manual 

x

 

1 Box with Packing Material 

 

NOTE: Carefully check all small wrappings, boxes, and envelopes to be sure all parts and supplies 
are accounted for. 

 

CALIBRATON GAUGE 

 
To check the calibration properly, the user of the micrometer should have the necessary gauge 
blocks on hand.  

The gauge blocks

 

can be ordered separately from TMI.  

See Section 3 

 

Specifications. 

 
 

SAVE THE BOX 
 

Remove the micrometer from the case with the greatest of care.  Do not use 
the pressure foot, the anvil or the spindle as a handle.  Grasp the instrument 
by the base only. 

 
Please save all the original packing material from the micrometer.  In the event the tester needs to 
be returned, it must be packaged in the original shipping carton after receiving approval and a 

Return Authorization Number (RA#) from TMI’s Customer Service Department.

 

 
 

FEATURES 

x

 

Digital readout and superior mechanical design

 

x

 

Serial output for simple data collection

 

x

 

Compact, for use throughout the laboratory and production floor

 

x

 

Special anvil diameters and dead weight loads available on request

 

 

digital-micrometer-ld3581-49-86-m44.pdf   7

digital-micrometer-ld3581-49-86-m44.pdf   7

15-6-2020   14:37:59

15-6-2020   14:37:59

Summary of Contents for 49-85





















Reviews: