background image

49-85/86/87 

Rev.E 

 

IMPORTANT SAFETY INSTRUCTIONS

 

Read all of these instructions carefully before operating the instrument. 

 

1.

 

Save these instructions for future reference. 

 
2.

 

Follow all warnings and instructions that are marked on the instrument.   

 
3.

 

Unplug the instrument from the wall outlet before cleaning.  Wipe the outside surfaces with a damp cloth 
only. 

 
4.

 

Do not use this instrument near water. 

 
5.

 

Do not place the instrument on an unstable cart, stand, or table. 

 

6.

 

Only operate the instrument from the type of power source indicated on the label. 
 

7.

 

For safety, this product is equipped with a three-wire grounding type plug.  This plug will only fit into a 
grounding type power outlet. If you are unable to insert the plug into the outlet, contact your electrician to 
replace the outlet with the proper type.  

Do not defeat the purpose of the grounding-type plug.

 

 
8.

 

Do not allow anything to rest on the power cord.  Do not locate this product where persons will walk on the 
cord.  

 
9.

 

If an extension cord is used with this product, make sure that the total ampere ratings of the product(s) 
plugged into the extension cord do not exceed the extension cord ampere rating.  Extension cords must have a 
minimum insulation rating of 600v. 

 

10.

 

Do not remove any panels from the tester.  Never push objects of any kind into any openings in the 

instrument’s c

overs. Failure to heed this warning could result in fire or electric shock.  Never spill liquid of 

any kind on the instrument. 

 
11.

 

Do not attempt to service this product yourself.  Opening or removing 
covers may expose you to dangerous high voltages.   
 

 
 

12.

 

At the end of its service life, dispose of the product according to the relevant statutory regulations. 

 

13.

 

Refer all servicing to Testing Machines’ Technical Support Staff: 

 

 

Testing Machines Inc. 

 

Customer Service Department 
40 McCullough Drive 
New Castle, DE 19720 USA 
Phone: (800) 678-3221 or (302) 613-5600 
Fax:  (302) 613-5619 
Email:  [email protected] 
Web:  www.testingmachines.com 

 
14.

 

Unplug the unit from the wall outlet and refer servicing to qualified service personnel under the following 
conditions: 

i

    When the power cord or plug is damaged or frayed. 

i

  If liquid has been spilled into the product. 

i

 

If the product has been exposed to rain or water. 

 

15.

 

Adjust only those controls that are covered by the operating instructions.  Improper adjustments of other 
controls may result in damage to the instrument and will often require extensive work by a technician to 
restore the unit to normal operation. 
 
 
 

digital-micrometer-ld3581-49-86-m44.pdf   3

digital-micrometer-ld3581-49-86-m44.pdf   3

15-6-2020   14:37:59

15-6-2020   14:37:59

Summary of Contents for 49-85





















Reviews: