background image

49-85/86/87

2

Rev.E

TESTING MACHINES, INC.

 

The Finest Test Equipment for all Industries

Worldwide Headquarters 

Sales and Service 

40 McCullough Drive 

New Castle, DE 19720 USA 

Phone:  302-613-5600 

Toll Free:  800-678-3221 

Fax:  302-613-5619 

www.testingmachines.com 

Dear Valued Customer: 

You are now the proud new owner of quality physical testing equipment manufactured by Testing 
Machines Inc., t

he industry’s leader for over 80

 years.  TMI has a long-standing commitment to 

quality products and customer satisfaction.   

To aid in setup, calibration, and operation of all Testing Machines Inc. equipment, we offer 
telephone assistance by our Technical Support Department, available Monday through Friday 
from 8:30 AM to 5:00 PM EST.  TMI also offers on-site Preventative Maintenance and Calibration 
service. 

Please take the time to fill out the postage paid Warranty Card completely and return it to us.  
Your comments make it possible for us to evaluate how well we are servicing your needs. 

In the unlikely event that your equipment requires warranty repair service, or if you need to 
arrange for non-warranty repair service, please follow the instructions on the repair policy page 
located in this manual.  Supplying the requested information on the repair policy page enables 
our Technical Support Staff to service your needs faster. 

Please contact us at (302) 613-5600 if additional information is required. 

Sincerely, 

Testing Machines, Inc. 

digital-micrometer-ld3581-49-86-m44.pdf   2

digital-micrometer-ld3581-49-86-m44.pdf   2

15-6-2020   14:37:58

15-6-2020   14:37:58

Summary of Contents for 49-85





















Reviews: