manualshive.com logo in svg

TME Xtrema, Instruction Manual, Page: 11 / 17

Share
Download
TME Xtrema Instruction Manual Download Page 11

11

TIP! 

For 

“

Volts minimum

”

 to display properly you should connect the battery to the Xtrema 

before you enter the Wattmeter mode. Otherwise the minimum voltage displayed will be zero 0.00. 
If you have already entered the Wattmeter mode simply push the joystick  

 left once then  

right to temporarily go to the main menu and then re enter the Wattmeter mode

Also note that at any time you want to reset the minimum and peak settings you may simply go 
back to the main menu temporarily as described above.

6. SETUP MENU

The setup menu allows you to customize the internal setting of the Xtrema. You enter the setup 
menu from the main menu by selecting ..setup.. and pressing the joystick to the

 right.

  Xtrema Main Menu:

o    Li Charger

f   

”

 Wattmeter  

f  

’

 

 ..setup..  

‘

Upon entering the setup menu you will see three options. The first is Li Setup which allows 
you to change charger settings such as volts per cell, the safety timer and the temperature cutoff. 
The second option 

Beep Options

 lets you set up how the Xtrema makes sounds. The third 

option 

Set Defaults

 merely restores all the factory default options.

Li Setup

Select LI SETUP from the setup menu and press the joystick to the

 right.

Choose one of the following by moving the up 

 or down 

buttons and press the joystick 

to the 

 right.

Volts / Cell

This setup menu allows you to change the maximum voltage that the Xtrema stops charging.  You can 
program the Xtrema to charge from 3.6 volts / cell to 4.20 volts / cell.  Note that this is a GLOBAL setting 
meaning that it will affect all of your memorized pack configurations.

Choose the desired voltage by moving the up 

 or down 

buttons and press the joystick to the 

 right 

when the displayed value is what you desire. You may abort the change by hitting the joystick 

 left.

Why change the Volts per cell?

Different Lithium chemistries require charging up to different voltages. You can charge Lithium Polymer 
packs lower to increase their longevity and for long term storage. The chart and descriptions below can 
help you select the right volts / cell. 

Recommended Volts/Cell

LiPo

M1

Charge

4.0 to 4.2 

3.6

Storage

3.7

none

Summary of Contents for Xtrema


















Reviews:

No comments