background image

 

172-65286MA-03  (DC3S-L)    6  Oct  2021

 

 

 

Use hoisting equipment for heavy objects (weighing 
approximately 20 kg (44 lb) or more). 

Failure to do so may result in back strain or other injury if the object 
should fall. 

Take measures to prevent people from coming into direct 
contact with product outlets. 

Failure to do so may result in burns or other injury from the 
discharge of fluids.

 

When disassembling or removing the product, wait until the 
internal pressure equals atmospheric pressure and the surface 
of the product has cooled to room temperature. 

Disassembling or removing the product when it is hot or under 
pressure may lead to discharge of fluids, causing burns, other 
injuries or damage.

 

Be sure to use only the recommended components when 
repairing the product, and NEVER attempt to modify the 
product in any way.

 

Failure to observe these precautions may result in damage to the 
product and burns or other injury due to malfunction or the 
discharge of fluids.

 

Do not use excessive force when connecting threaded pipes to 
the product. 

Over-tightening may cause breakage leading to fluid discharge, 
which may cause burns or other injury.

 

Use only under conditions in which no freeze-up will occur. 

Freezing may damage the product, leading to fluid discharge, which 
may cause burns or other injury. 

 

Use only under conditions in which no water hammer will 
occur. 

The impact of water hammer may damage the product, leading to 
fluid discharge, which may cause burns or other injury.

 

 

 

CAUTION 

Summary of Contents for DC3S-L















Reviews: